background image

TROUBLESHOOTING WARNINGS

LET PUMP COOL FOR A MINIMUM OF 2 HOURS BEFORE 

ATTEMPTING TO SERVICE. 

Submersible pumps contain oil that 

become pressurized and hot under normal operating conditions.

LAISSER REFROIDIR LA POMPE PENDANT AU MOINS 2 HEURES 

AVANT D’ESSAYER DE LA RÉPARER. 

Les pompes submersibles 

contiennent de l’huile qui devient pressurisée et chaude dans des 
conditions normales de fonctionnement.

1.  Submersible pump models have permanently lubricated 

bearings and require no additional lubrication.

2.  Submersible pump contains dielectric oil for cooling.  

Dielectric oil can be harmful to the environment.  Follow 
state environmental laws when disposing of pump.

3.  The AC pump motor is equipped with automatic resetting 

thermal protector and may restart unexpectedly.  Protector 
tripping is an indication of motor overloading as a result of 
operating the pump at low heads, excessively high or low 
voltage, inadequate wiring, incorrect motor conditions, or at 
the end of its life.

AC ROUTINE SUMP MAINTENANCE

The pump system should be inspected 3-4 times per year for 
movement or buildup of debris on the switch or float. Reposi-
tion system if it has moved. Remove any debris that could 
interfere with the operation of the switches. Lack of proper 
routine maintenance will void warranty.

• Make sure the system is plugged in to a working ground fault 
circuit interrupter (GFCI) outlet and the cord is in good shape. 
In damp areas, GFCI breakers may trip, effectively shutting off 
the sump pump. Check in on your sump pump and reset the 
GFCI if necessary. Replace pump if GFCI continues to trip.

• Ensure the system is upright. Vibrations during operation can 
cause it to fall or tilt onto one side. This can jam the float so it 
can’t activate the pump.

• Pour a bucket of water into the pit to make sure the AC 
pump starts automatically and the water drains quickly once 
the pump is on. If the pump doesn’t start, have it serviced or 
replaced.

• Check the inlet screen and clear away any small stones or 
debris.

8

www.waynepumps.com

Operating Instructions and Parts Manual

Summary of Contents for WSS30Vn













Reviews: