background image

Six Loop Switch Controller 

                   

LIGHT LINK 

     

EZ-5645S 

Copyright 

© 

2016 by 

WDH.,CO 

All rights reserved. No part of this document may be reproduced by any means, 
without written permission of the copyright owner.

                                               

http://www.wdh.com.tw

 

1/10

 

 

 

  We all know that the relay is a certain life, the relay inside 

the metal reed will be damaged, then need to rely on 

professionals to repair replacement, not only the high cost 

and more disputes. 

The new design of the S5645 to complete the maintenance 

and replacement to overcome the problem, each relay 

device is easy to replace the modular structure, the 

efficient future maintenance, to avoid the maintenance 

process of the many problems. 

The new design of the 5645S also confused the previous 

engineering staff to solve the actual lighting feedback 

problems, with current sensing components RL-PB01 can 

accurately and efficiently identify the actual light switch 

status, "WYSIWYG" has been the system operator Efforts 

to implement the objectives, using 5645S will make your 

project planning more perfect!

 

Easy To 
Replacement 

Introduction 

Summary of Contents for LIGHT LINK EZ-5645S











Reviews: