background image

Dosing Device Foamdos V6

 

 
 

Index:  01 

Date modified: 26/08/2019 

OI No.: BA DW 025-00 Foamdos V6 EN.DOCX 

Page 25 of 37

 

6.6

 

Adjust the foam consistency 

The  consistency  of  the  massage  foam  is  set  via  the  water 
volume. The setting is done at the needle valve (6). 
 

Turn clockwise: 
The water flow is decreased, the foam becomes firmer. 
 
Turn counter-clockwise: 

The water flow is increased, the foam becomes more liquid. 
 
 
 

 
 
 
 

 
 

6.7

 

Replenish consumables 

Replace the canister with foam concentrate 

a)

 

Unscrew the lid of the new canister. 

b)

 

Place the suction lance in the canister. 

c)

 

Screw the suction lance’s lid on the canister. 

d)

 

Check that the suction lance reaches the bottom of 
the canister. 

e)

 

If necessary, push suction lance downward.  

f)

 

Vent foam line 
After replacing the canister, the foam line may be 
empty. Press the “

Foam

” push button on the button 

plate until the foam runs out at the withdrawal point. The display shows 

“Test foam”

 

Figure 18, Needle valve

 

 

Figure 19, Suction lance

 

Summary of Contents for Foamdos V6













































Reviews: