CPR Touch XL, Steuereinheit
Index: 02 Änderungsdatum: 20.03.2017
BA-Nr.: BA MR 001 02 Steuereinheit CPR Touch XL DE.docx
Seite 49 von 68
16.
Reinwasser extern
ALARM:
Externer Durchflusssensor mel-
det zu geringen Durchfluss. Die
Dosierungen und die Treibwas-
serpumpe werden gestoppt.
Schwimmbadumwälzung prüfen; wenn diese OK
ist, dann den Durchflusssensor prüfen.
17.
Flockung Leckage
ALARM:
An der Flockungs-Dosierpum-
pe hat der Schlauchbruchsen-
sor angesprochen. Die Flo-
ckungsdosierung wird ge-
stoppt.
Dosierschlauch der Pumpe prüfen und ggf.
erneuern; wenn dieser OK ist, dann das
Dosierventil prüfen.
18.
Säure Leckage
ALARM:
An der Säure-Dosierpumpe
hat der Schlauchbruchsensor
angesprochen. Die Säuredo-
sierung wird gestoppt.
Dosierschlauch der Pumpe prüfen und ggf.
erneuern; wenn dieser OK ist, dann das
Dosierventil prüfen.
19.
Desinfektion Leckage
ALARM: (nur für Typ 2S)
An der Desinfektions-Dosier-
pumpe hat der Schlauch-
bruchsensor angesprochen.
Die Desinfektionsdosierung
wird gestoppt.
Dosierschlauch der Pumpe prüfen und ggf.
erneuern; wenn dieser OK ist, dann das
Dosierventil prüfen.
20.
Extern Off
MELDUNG:
Die Steuereinheit ist durch die
Zentralleittechnik deaktiviert.
Es erfolgt keine Dosierung,
keine Beckenwassererwär-
mung, keine Alarmmeldung.
Das Dosiergerät stoppt.
Keine Maßnahme, da eine externe Abschaltung
erfolgt ist.
21.
Dosierzeitüberschrei-
tung ALARM:
Eine dynamische Dosierzeit
wurde überschritten. Der ent-
sprechende Ausgang ist blo-
ckiert. Aus Platzgründen wird
keine Unterscheidung der ein-
zelnen Kanäle vorgenommen!
Dosierschnecke und Dosierpumpen auf Defekt
und Blockierung prüfen. Defekt bzw. Blockierung
beseitigen. (siehe auch Abschnitt 7 zur entspre-
chenden Dosiereinheit).
Einstellung der Dosierleistung prüfen, ob diese zu
gering ist.
22.
Hochchlorung aktiv
MELDUNG:
Die Hochchlorung / Filterdes-
infektion ist aktiv.
Keine Maßnahme
23.
ECO-Betrieb
MELDUNG:
Die Anforderung „ECO-Be-
trieb“ vom Zentralschalt-
schrank steht an.
Keine Maßnahme
Fehlfunktion ohne Anzeige im Display:
1.
Das Display ist dunkel und das Gerät aus:
a)
Keine Versorgungsspannung:
Versorgungsspannung wiederherstellen
b)
Die Hauptsicherung unten links am Gehäuse ist durchgebrannt:
Sicherung erneuern
c)
Die Sicherung F1 am Netzteil ist durchgebrannt:
Sicherung erneuern
d)
Das Netzteil ist defekt:
Netzteil erneuern
2.
Beim Abstellen des GRANUDOS läuft die Spülwanne über:
In diesem Fall, ist eines der folgenden Elemente undicht:
a)
Schwimmerventil:
Membrane erneuern
b)
Schaltkörper im Saugrohr:
Dichtung erneuern
c)
Druckhalteventil an der Treibwasserpumpe ist undicht oder falsch eingestellt:
Membrane erneu-
ern und Druckhalteventil einstellen
Zur Vorgehensweise siehe Betriebsanleitung Teil 1 Dosiertechnik,
unter Abschnitt 7.1, Gerätewartung
.