background image

Dear music lover,

Congratulations  on  the  purchase  of  your  new  Perpetuum 
Ebner (PE) turntable.
This product has been designed and manufactured with the 
greatest care. 

Please, take note of the enclosed safety information and read 
the  operating  instructions  carefully  before  you  set  up  and 
operate the device.

SAFETY INFORMATION:
PLEASE READ CAREFULLY BEFORE OPERATING YOUR 
UNIT !

CAUTION:
To  reduce  risk  of  electric  shock,  do  not  remove  the  cover. 
There are no user-serviceable parts inside.

This symbol on the product or on its packaging indicates that this product 
must  not  be  disposed  of  with  your  other  household  waste.  Instead,  it  is 
your responsibility to dispose of your waste equipment by handing it over 
to  a  designated  collection  point  for  the  recycling  of  waste  electrical  and 
electronic equipment. The separate collection and recycling of your waste 
equipment at the time of disposal will help to conserve natural resources 
and ensure that it is recycled in a manner that protects human health and 
the environment.
For more information about where you can drop off your waste equipment 
for recycling, please contact your local city office, your household waste 
disposal service or the shop where you purchased the product.

This product was tested and complies with all the requirements 
for the CE Mark.

IMPORTANT: Disposal of waste equipment by users in private
households in the European Union.

Tradition verpflichtet

3

Summary of Contents for PE 4040

















Reviews: