28 |
P a g e
TRIPLE SLIDING SHUTTERS INSTALLATION
INSTRUCTIONS
1.
FRAME ASSEMBLY
If this is a 2, 3 or 4 sided application, then refer to Diagram C for frame assembly
instructions. Once the frames are assembled, installation holes are required by
using a 10mm drill bit.
A.
For an inside mount, drill a 10mm hole through the first layer of vinyl, within the
mounting area every 250mm starting at each end of the frames.
B.
For an outside mount, drill a 10mm hole through the first layer of vinyl at the
front edge of the reveal of the frame every 250mm.
2.
TOP FRAME INSTALLATION
A.
For an inside mount, fasten the top frame to the opening, making sure it is
level; shim
to level if necessary.
B.
For an outside mount, set the frame against the wall. Level the top and fasten
the top frame to the wall with the provided installation screws.
3.
WHEEL CARRIERS
Insert wheel carriers inside each aluminium track. Two carriers are assigned to
each panel so check the panel configuration to determine the correct number of
carriers in each track.
4.
ALUMINUM TRACKS
Mount aluminium tracks to the extreme left of the opening of the frame by
screwing through the pre-drilled holes in the track to the extrusion lines on the
underside of the top frame (See Diagram D and Diagram E).
5.
ATTACH DOUBLE PANELS IF APPLICABLE
When two panels are to be attached, lay panels face up and side by side on the
floor. Remove the two interior top jamb caps. Insert the panel joiner by sliding it
into the two interior jambs (See Diagram G). Place the jamb caps back onto the
top jambs.
6.
ATTACH LIGHT BLOCK FOR OPEN SLIDING
2 pieces of vertical jamb will be supplied for every overlap when Open Sliding is
ordered. One piece of vertical jamb is mounted at the back of the interior edge of
the front panel, while the second piece is mounted at the front interior edge of the
rear panel. For either option, drill a 10mm hole starting at the top, every 500mm
through the first two layers of vinyl. Screw the vertical jamb to the panel and cap
holes with button plugs.
7.
HANG SHUTTERS
Push the door plates onto the adjustable nut of the wheel carriers.
8.
LEVEL PANELS
Adjust one panel in line with the window mullion, adjust the other panels in line with
this panel. Now lock the panels by tightening the 11mm lock nut.
Summary of Contents for Eclipse Shutters
