background image

 Warranty

5. General

(a) Most warrantable failures show up within the fi rst few weeks of use. These failures are usually straightforward and 
warranty assessment is relatively easy.
(b) Failures relating to cutter decks and belts need careful investigation, as the cause may not always be straightforward. 
Look for damage to blades and pulleys especially when the cutter belt or blade boss have snapped or cracked as this could be 
due to impact damage.
(c) Customers should always refer to the operator/instruction manual when any disputed problem arises, you will fi nd most 
areas covered within the manual.

Protecting your machine

Maintenance

Regular maintenance of your Webb machine is essential to ensure it operates, safely, effi ciently and therefore reducing the 
environmental impact.
It is the owner’s responsibility to ensure that their Webb machine is maintained at specifi c intervals. Any approved Webb 
service dealer can undertake a service, which are specialised in our products and will be aware of your particular machine 
and any technical updates which will save valuable time & money.
If you are using your machine in dry, dusty or high temperatures, you will need to service the machine more regularly.

Fuel

Due to ongoing efforts by fuel companies to reduce emissions, unleaded petrol will oxidize & deteriorate in storage overtime, 
leaving residue from detergent components.
Fuel deterioration problems may occur when petrol is stored for over 30 days. If you are planning to store fuel for over 
30 days, we recommend you add Handy Parts Sure-Start fuel stabilizer to fresh fuel after purchasing. Sure-Start cannot 
reconstitute stale fuel.

Storage

When storing your machine for an extended period, we do recommend that you follow the instructions of engine instruction 
manual.
Always store the fuel in a clean, approved and sealed container. If the container is steel, ensure it is not corroded.
If the container is not fi lled to its recommended capacity, air can accelerate fuel deterioration.
Always store fuel away from direct sunlight, in a dark, cool environment.

Service Record

Your servicing Webb approved dealer will stamp & date the below relevant sections, when the correct service actions have 

been completed. 

PLEASE ENSURE THE SERVICE BOOK IS AVAILABLE FOR THE DEALER, DURING SERVICE WORK.

1st Service

This must be stamped by an approved service dealer to 

qualify for a free second year warranty.

24 Months

Date

Date

36 Months

12 Months

Date

INSTRUCTION MANUAL

SERVICE BOOK

Summary of Contents for 1938123001





































Reviews: