Webb WERR17P, Operator'S Manual & Parts List

1.   Drive Lever 

(WERR17SP Only)

2.  Brake (OPC) Lever

3.  Fuel Tank

4.   Air Filter / Primer Bulb

2

5

6

7

8

4

1

3 

9

5. Spark Plug    

7.  Oil Filter and Dipstick

9.   Grass Collection Bag  

8.  Recoil Rope  

6.  Muffler / Exhaust 

ASSEMBLY INSTRUCTIONS - LF43SPBR 17" Roller model

Remove the machine and all components from the carton.  Assemble as follows: 

1a.

 Select the left hand 

the two studs on the 

right hand side of the 

mower, 

ensure that the 

U shape of the handle 

goes towards the 

chassis 

. 

2.

  Select the right hand 

the two studs on the left

hand side of the mower,

ensure that the U shape of the handle

goes towards the 

chassis. Fix with two 

cap head nuts. 

4. 

wire recoil rope guide 

to the right hand clamp 

bolt, this goes on the 

inside of the handle

between the handle 

and the securing nut. 

6.  Fit the Operator 

Presence Cable, 

remove the lever from 

its mounting by easing it

from the handle, attach 

the Z cable end to the 

OPC lever as shown in 

lever to the handle.  

8. Ensure you have 

attached the correct 

cable to the correct 

lever. 

 8)

3.

  Assemble the upper 

handle to the lower 

handle using the two 

clamp bolts and nuts, 

ensuring that the large 

washer goes against the 

clamp handle on the 

outside of the handle 

as per the photo. 

5.

 Tension clamp bolts 

to ensure the handles 

7. Fit the Self Propelled 

drive cable, again 

remove the lever from 

its mounting by gen-

tly easing it from the 

handle, attach the Z 

cable end to the Self 

Propelled drive lever as 

the lever to the handle. 

9.  Fit the cable router 

to the handle using the 

securing bolt supplied, 

the inside of the handle 

as per the photo. 

10. Hold in the 

Operator control handle 

and pull on the recoil 

starter rope so you can 

attach it through the 

wire recoil rope guide. 

1b.

 Fix with two cap 

head nuts. 

11

. 

Set the grass bag 

and grass bag frame 

together then lock the 

plastic buckles on the 

grass bag frame.  

ASSEMBLY INSTRUCTIONS - LF43SPBR 17" Roller model

Remove the machine and all components from the carton.  Assemble as follows: 

1a.

 Select the left hand 

the two studs on the 

right hand side of the 

mower, 

ensure that the 

U shape of the handle 

goes towards the 

chassis 

. 

2.

  Select the right hand 

the two studs on the left

hand side of the mower,

ensure that the U shape of the handle

goes towards the 

chassis. Fix with two 

cap head nuts. 

4. 

wire recoil rope guide 

to the right hand clamp 

bolt, this goes on the 

inside of the handle

between the handle 

and the securing nut. 

6.  Fit the Operator 

Presence Cable, 

remove the lever from 

its mounting by easing it

from the handle, attach 

the Z cable end to the 

OPC lever as shown in 

lever to the handle.  

8. Ensure you have 

attached the correct 

cable to the correct 

lever. 

 8)

3.

  Assemble the upper 

handle to the lower 

handle using the two 

clamp bolts and nuts, 

ensuring that the large 

washer goes against the 

clamp handle on the 

outside of the handle 

as per the photo. 

5.

 Tension clamp bolts 

to ensure the handles 

7. Fit the Self Propelled 

drive cable, again 

remove the lever from 

its mounting by gen-

tly easing it from the 

handle, attach the Z 

cable end to the Self 

Propelled drive lever as 

the lever to the handle. 

9.  Fit the cable router 

to the handle using the 

securing bolt supplied, 

the inside of the handle 

as per the photo. 

10. Hold in the 

Operator control handle 

and pull on the recoil 

starter rope so you can 

attach it through the 

wire recoil rope guide. 

1b.

 Fix with two cap 

head nuts. 

11

. 

Set the grass bag 

and grass bag frame 

together then lock the 

plastic buckles on the 

grass bag frame.  

ASSEMBLY INSTRUCTIONS - LF43SPBR 17" Roller model

Remove the machine and all components from the carton.  Assemble as follows: 

1a.

 Select the left hand 

the two studs on the 

right hand side of the 

mower, 

ensure that the 

U shape of the handle 

goes towards the 

chassis 

. 

2.

  Select the right hand 

the two studs on the left

hand side of the mower,

ensure that the U shape of the handle

goes towards the 

chassis. Fix with two 

cap head nuts. 

4. 

wire recoil rope guide 

to the right hand clamp 

bolt, this goes on the 

inside of the handle

between the handle 

and the securing nut. 

6.  Fit the Operator 

Presence Cable, 

remove the lever from 

its mounting by easing it

from the handle, attach 

the Z cable end to the 

OPC lever as shown in 

lever to the handle.  

8. Ensure you have 

attached the correct 

cable to the correct 

lever. 

 8)

3.

  Assemble the upper 

handle to the lower 

handle using the two 

clamp bolts and nuts, 

ensuring that the large 

washer goes against the 

clamp handle on the 

outside of the handle 

as per the photo. 

5.

 Tension clamp bolts 

to ensure the handles 

7. Fit the Self Propelled 

drive cable, again 

remove the lever from 

its mounting by gen-

tly easing it from the 

handle, attach the Z 

cable end to the Self 

Propelled drive lever as 

the lever to the handle. 

9.  Fit the cable router 

to the handle using the 

securing bolt supplied, 

the inside of the handle 

as per the photo. 

10. Hold in the 

Operator control handle 

and pull on the recoil 

starter rope so you can 

attach it through the 

wire recoil rope guide. 

1b.

 Fix with two cap 

head nuts. 

11

. 

Set the grass bag 

and grass bag frame 

together then lock the 

plastic buckles on the 

grass bag frame.  

ASSEMBLY INSTRUCTIONS - LF43SPBR 17" Roller model

Remove the machine and all components from the carton.  Assemble as follows: 

1a.

 Select the left hand 

the two studs on the 

right hand side of the 

mower, 

ensure that the 

U shape of the handle 

goes towards the 

chassis 

. 

2.

  Select the right hand 

the two studs on the left

hand side of the mower,

ensure that the U shape of the handle

goes towards the 

chassis. Fix with two 

cap head nuts. 

4. 

wire recoil rope guide 

to the right hand clamp 

bolt, this goes on the 

inside of the handle

between the handle 

and the securing nut. 

6.  Fit the Operator 

Presence Cable, 

remove the lever from 

its mounting by easing it

from the handle, attach 

the Z cable end to the 

OPC lever as shown in 

lever to the handle.  

8. Ensure you have 

attached the correct 

cable to the correct 

lever. 

 8)

3.

  Assemble the upper 

handle to the lower 

handle using the two 

clamp bolts and nuts, 

ensuring that the large 

washer goes against the 

clamp handle on the 

outside of the handle 

as per the photo. 

5.

 Tension clamp bolts 

to ensure the handles 

7. Fit the Self Propelled 

drive cable, again 

remove the lever from 

its mounting by gen-

tly easing it from the 

handle, attach the Z 

cable end to the Self 

Propelled drive lever as 

the lever to the handle. 

9.  Fit the cable router 

to the handle using the 

securing bolt supplied, 

the inside of the handle 

as per the photo. 

10. Hold in the 

Operator control handle 

and pull on the recoil 

starter rope so you can 

attach it through the 

wire recoil rope guide. 

1b.

 Fix with two cap 

head nuts. 

11

. 

Set the grass bag 

and grass bag frame 

together then lock the 

plastic buckles on the 

grass bag frame.  

ASSEMBLY INSTRUCTIONS - LF43SPBR 17" Roller model

Remove the machine and all components from the carton.  Assemble as follows: 

1a.

 Select the left hand 

the two studs on the 

right hand side of the 

mower, 

ensure that the 

U shape of the handle 

goes towards the 

chassis 

. 

2.

  Select the right hand 

the two studs on the left

hand side of the mower,

ensure that the U shape of the handle

goes towards the 

chassis. Fix with two 

cap head nuts. 

4. 

wire recoil rope guide 

to the right hand clamp 

bolt, this goes on the 

inside of the handle

between the handle 

and the securing nut. 

6.  Fit the Operator 

Presence Cable, 

remove the lever from 

its mounting by easing it

from the handle, attach 

the Z cable end to the 

OPC lever as shown in 

lever to the handle.  

8. Ensure you have 

attached the correct 

cable to the correct 

lever. 

 8)

3.

  Assemble the upper 

handle to the lower 

handle using the two 

clamp bolts and nuts, 

ensuring that the large 

washer goes against the 

clamp handle on the 

outside of the handle 

as per the photo. 

5.

 Tension clamp bolts 

to ensure the handles 

7. Fit the Self Propelled 

drive cable, again 

remove the lever from 

its mounting by gen-

tly easing it from the 

handle, attach the Z 

cable end to the Self 

Propelled drive lever as 

the lever to the handle. 

9.  Fit the cable router 

to the handle using the 

securing bolt supplied, 

the inside of the handle 

as per the photo. 

10. Hold in the 

Operator control handle 

and pull on the recoil 

starter rope so you can 

attach it through the 

wire recoil rope guide. 

1b.

 Fix with two cap 

head nuts. 

11

. 

Set the grass bag 

and grass bag frame 

together then lock the 

plastic buckles on the 

grass bag frame.  

ASSEMBLY INSTRUCTIONS - LF43SPBR 17" Roller model

Remove the machine and all components from the carton.  Assemble as follows: 

1a.

 Select the left hand 

the two studs on the 

right hand side of the 

mower, 

ensure that the 

U shape of the handle 

goes towards the 

chassis 

. 

2.

  Select the right hand 

the two studs on the left

hand side of the mower,

ensure that the U shape of the handle

goes towards the 

chassis. Fix with two 

cap head nuts. 

4. 

wire recoil rope guide 

to the right hand clamp 

bolt, this goes on the 

inside of the handle

between the handle 

and the securing nut. 

6.  Fit the Operator 

Presence Cable, 

remove the lever from 

its mounting by easing it

from the handle, attach 

the Z cable end to the 

OPC lever as shown in 

lever to the handle.  

8. Ensure you have 

attached the correct 

cable to the correct 

lever. 

 8)

3.

  Assemble the upper 

handle to the lower 

handle using the two 

clamp bolts and nuts, 

ensuring that the large 

washer goes against the 

clamp handle on the 

outside of the handle 

as per the photo. 

5.

 Tension clamp bolts 

to ensure the handles 

7. Fit the Self Propelled 

drive cable, again 

remove the lever from 

its mounting by gen-

tly easing it from the 

handle, attach the Z 

cable end to the Self 

Propelled drive lever as 

the lever to the handle. 

9.  Fit the cable router 

to the handle using the 

securing bolt supplied, 

the inside of the handle 

as per the photo. 

10. Hold in the 

Operator control handle 

and pull on the recoil 

starter rope so you can 

attach it through the 

wire recoil rope guide. 

1b.

 Fix with two cap 

head nuts. 

11

. 

Set the grass bag 

and grass bag frame 

together then lock the 

plastic buckles on the 

grass bag frame.  

BOX CONTENTS / PRODUCT DIAGRAM

×1

1.

×1

7.

×1

4.

×1

2.

×2

8.

×1

9.

×2

10.

×1

5.

×1

3.

×4

6.

What 

y

ou get with 

your mower

Please read & understand this manual, paying particular attention to the safety instructions, before use.

Operator’s Manual & Parts List

29 Oct 2015

193864001

51cm Self Propelled

High Wheeled

Steel Deck Lawnmower

WER51SPHW

1.  Petrol Engine Mower

2.   Instruction Manual

3.  Rear Grass Catcher

4.  Rope Guide

5.   Spanners

6.  Bolt and Nut Assembly

7.  Spark Plug Socket

8.  Cable Ties

9.  Mulch Plug

10.  Quick Release Handle

INSTRUCTION MANUAL