background image

CR 7 HD

Operation

Prior to starting work the owner of the compactor must be familiar with the work environment. The 

work environment includes obstacles in the work and traffic area, the bearing capacity of the ground, 

as well as the necessary safeguarding of the construction site in the area adjacent to public traffic; 

and it includes compliance with traffic regulations.

The soil compactor should only be operated when the protective fixtures are mounted. The protective 

fixtures must all be in functional condition.

At least once per shift the compactor must be checked for apparent defects. If there are apparent 

defects then operation of the compactor must be stopped immediately, and the responsible person 

must be informed. Prior to restarting, compactor malfunctions that have occurred must be corrected.

Always maintain adequate clearance to the edges of pits and embankments.

Do not drive at ninety degrees to slopes to prevent the compactor from tipping over.

After work has been concluded secure the compactor in accordance with statutory regulations, 

particularly in the area of public traffic surfaces.

Operation under difficult conditions

Never inhale the exhaust gas; it contains carbon monoxide, a colorless and odorless gas that 

is extremely hazardous, which, if inhaled even briefly, can cause unconsciousness and death. 

Therefore, never operate the engines in enclosed areas or in areas that are poorly ventilated 

(tunnels, caves, etc.). Exercise particular caution when operating the engine in the vicinity of 

people and livestock.

Maintenance and repair work

Only use 

original Weber spare parts

 to ensure reliable and safe operation for maintenance or repair 

work.

Hydraulic hose lines must be checked at regular intervals in accordance with standard engineering 

practice, or they must be replaced at appropriate intervals, even if no signs of safety-relevant defects 

are present.

Adjusting tasks, maintenance tasks, and inspection tasks must be executed on schedule as specified 

in this operating and maintenance manual. These activities should only be executed by instructed 

personnel.

For repair, service, or inspection work the engine of the compactor must be safeguarded against 

unintentional starting. 

All pressurized lines, particularly hydraulic lines and lines of the injection system of the drive motor 

must be depressurized before performing maintenance or repair tasks.

For maintenance and repair tasks the compactor must be parked on a level and stable substrate and 

must be secured from rolling off or tipping over.

Heavy components and assemblies must be secured to and lifted by hoisting machines that can 

bear their weight when they are replaced. Ensure that no hazard is caused by raising components or 

assemblies.

Do not position yourself or work under suspended loads.

If lubricating oils and fuel come into contact with skin, they can cause skin cancer. Upon contact 

with the skin, clean affected skin with suitable cleaning agent without delay.

Summary of Contents for CR 7 HD

























Reviews: