background image

CR 9-II CCD 2.0 

5

Safety guidelines

General

All safety instructions must be read and complied with, as non-compliance will result in

– danger to life and limb of the user,
– impairments to the machine or other property.

In addition to the operating manual, the accident-prevention regulations in the country where 

the appliance is used must be complied with.

Intended use

The soil compactor should only be used if it is in a technically faultless condition, as intended, 

in a safety-conscious and hazard-conscious manner, and in compliance with the instructions in 

the operating manual. Malfunctions that impair safety must be eliminated without delay.

The CR 9 CCD 2.0 compactor is designed exclusively for compacting 
– sand,
– gravel,
– asphalt, crushed rock,
– low-cohesive mixed material.
Any other use of the soil compactor is considered to be improper use for which the owner shall be 

exclusively responsible. All liability is rejected if damage occurs due to non-compliance with 

this provision. This risk is borne solely by the user.

Easily foreseeable misuse

Any use for which the machine is not intended.

Operation

Soil compactors are only permitted to be operated by suitable persons of or above the age of 18. 

Personnel must be instructed in how to guide the compactor by the owner or by the owner’s 

assigned personnel. 

The machine operator must comply with traffic regulations. If instructions that affect safety are given 

by third parties, then the operator must be authorized to reject these instructions.

Unauthorized persons are forbidden from being in the area of the soil compactor during 

the compacting process.

Protective equipment

This machine is capable of exceeding the permissible sound level of 80 dB(A). The owner might also 

face additional dangers when using the machine. Precautionary action must therefore be taken.

Protective equipment includes:

Hearing protection 

Hard hat 

Safety shoes 

Protective gloves 

Summary of Contents for CR 9-II

































Reviews:

Related manuals for CR 9-II