`çãéäÉíÉ=háí==^`qolp=
`çãéäÉíáçå=çÑ=~ëëÉãÄäó=Öêçìéë
629
630
701
210
560
479
1023
1
1
1
12
12
24
24
1026
479
1028
1027
7
397
355
12
217
80-e.DOC / K-Actros
Page 11
Mounting the switch panel into the cab ill. 14
Battery plate, side- and front covers ill. 15
NQ
jçìåíáåÖ=íÜÉ=ëïáíÅÜ=é~åÉä=áåíç=íÜÉ=Å~Ä=
The jacks 701 attached to the switch panel are clipped into the
matching slots in the lower rear panel. The insulating discs, red 629
and black 630, are attached from the outside and secured with the
knurled nuts 560. The black insulating disc serves to identify the jack
with the two black conductors!
When installing the rear panel make sure that the solder lugs of
the jacks do not touch!
NR
_~ííÉêó=éä~íÉI=ëáÇÉJ=~åÇ=Ñêçåí=ÅçîÉêë=
15.1 Battery plate
Slide one square nut 12 into each groove on both lower fixing frames
on the side panels. From inside press the battery plate 1023 -
thereby the cut out shows in direction of the dashboard - horizontal
between the side panels. Use screws 1 to fix the battery plate under-
neath the fixing frames.
15.2 Mounting the fenders with mud flaps
Slide one square nut 12 into the slot of the lower fixing frame on the
left side panel. Attach the pre-mounted left fender under the cab, so
that the fixing edge of the fender fits above the lower rear panel. Use
two tapping screws 479 and washers 24 to connect from underneath
the following parts: left mud flap 1027, fixing device of the fender and
lower rear panel. The fixing device of the fender has to be secured at
the following points: with one screw 1 to the side panel, and with two
countersunk screws 355 and nuts M3 to the front panel. Attach the
right fender with the right mud flap 1028 in the same way.
15.3 Assembly of the front covering
Set the bumper with the lamp units previously added to the front panel
and fix it from inside with two countersunk screws 7. Above the
bumper press the radiator grille 1026 to the front panel and fix it from
inside with four tapping screws 397. Afterwards press the Mercedes
Star 217 into the opening provided for on the radiator grille.
Qty.
No. Assembly part
4
210 Knurled nut M5
2
560 Knurled nut M6
1
629 Insulating disc, red
Qty.
No. Assembly part
1
630 Insulating disc, black
2
701 Jack bush 3.5mm
B-80-9
B-80-8
Qty.
No. Assembly part
4
--- Nut M3
6
1 Screw M3 x 6
2
7 Countersunk screw
M3 x 6
6
12 Square nut M3
4
24 Washer 2.2
1
217 Mercedes star
4
355 Countersunk screw
M3 x 8
Qty.
No. Assembly part
4
397 Tapping screw 2.2 x 6.5
4
479 Tapping screw 2.2 x 9.5
1
1023 Battery plate ACTROS
1
1026 Radiator grille ACTROS
1
1027 Mud flap -lh- ACTROS
1
1028 Mud flap -rh- ACTROS
Switch panel
to front PCB
to battery
to blinker switch
to rear PCB
to 7-pole socket
terminal for roof
to speed controller
to charging cable