Weed Eater 184404, Owner'S Manual

20

TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 20) 

The mower blade drive belt may be replaced without tools.  
Park the tractor on level surface.  Engage parking brake.  

BELT REMOVAL -
•      Place attachment clutch in “DIS EN GAGED” po si tion.
•      Move at tach ment lift lever forward to lower mower to 

its lowest position.

•      Roll belt off engine pulley.
•      Disconnect R.H. suspension arm from rear deck brack et 

by removing retainer spring.

•      Work belt off both mandrel pulleys and idler pulleys.
•      Pull belt away from mower. 

BELT INSTALLATION -
•      Work new belt around both mandrel pulleys and idler 

pulleys.

•      Install new belt into engine pulley grove.
•      Reconnect R.H. suspension arm and secure with re-

 tain er spring.

•     Make sure belt is in all pulley grooves and inside all 

belt guides.

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground 
or driveway.  Make sure tires are properly infl ated (See 
“PROD UCT SPECIFICATIONS” section of this manual).   If 
tires are over or underinfl ated, you will not properly adjust 
your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 16 and 17)
•      Raise mower to its highest position.
•         At the midpoint of both sides of mower, measure height 

from bot tom edge of mower to ground.   Distance “A” 
on both sides of mower should be the same or within 
1/4" of each other.

•     If adjustment is necessary, make adjustment on one 

side of mower only.

•      To raise one side of mower, tighten lift link ad just ment 

nut on that side.

•      To lower one side of mower, loosen lift link ad just ment 

nut on that side.

NOTE

:  Three full turns of adjustment nut will change mower 

height about 1/8".
•      Recheck measurements after adjusting.

NUT "E"

"D"

"D"

MANDREL

FIG. 18

NUT "F"

FRONT LINKS

FIG. 19

FRONT-TO-BACK ADJUSTMENT (See Figs. 18  and 19) 

IMPORTANT:

  DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE 

FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, 
BE SURE TO AD JUST BOTH FRONT LINKS  EQUAL LY  SO 

MOWER  WILL STAY LEVEL SIDE-TO-SIDE.     

To obtain the best cutting results, the mower housing 
should be adjusted so that the front is approximately 1/8" 
to 1/2" lower than the rear when the mower is in its high-
est position.

Check adjustment on right side of tractor.  Measure dis tance 
“D” directly in front and behind the mandrel at bottom edge 
of mower housing as shown.
•      Before making any necessary adjustments, check that 

both front links are equal in length.  

•      If links are not equal in length, adjust one link to same 

length as other link.

•     To lower front of mower loosen nut “E” on both front 

links an equal number of turns.

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

FIG. 16

SUSPENSION ARM

LIFT LINK 
ADJUSTMENT 
NUT

FIG. 17

“A”

“A”

BOTTOM EDGE OF 
MOWER
TO GROUND

BOTTOM EDGE 

OF MOWER

TO GROUND

GROUND LINE

TRUNNION

•     When distance “D” is 1/8" to 1/2" lower at front than 

rear, tighten nuts “F” against trunnion on both front 
links.

•      To raise front of mower, loosen nut “F” from trunnion on 

both front links. Tighten nut “E” on both front links an 
equal number of turns. The two front links must remain 
equal in length.

•         When distance “D” is 1/8" to 1/2" lower at front than rear, 

tighten nut “F” against trunnion on both front links.

•      Recheck side-to-side adjustment.