background image

11

GENERAL RECOMMENDATIONS

Always observe safety rules when performing any main-

 te nance.
•  Before each use check for loose fasteners.
•  Clean unit thoroughly after each use.

BLADE CARE

For best results, mower blade must be kept sharp.  Re place 

bent or damaged blade.
•  See BLADE CARE instructions in your riding mower 

owner's manual.

 

 

CAUTION: BEFORE PERFORMING ANY 

MAIN TE NANCE, SERVICE OR AD JUST-

 MENTS:

 

•  Depress clutch brake pedal fully and 

set parking brake.

 

• 

Place gearshift/motion control lever in 

"NEU TRAL" position.

 

• 

Place clutch control in "DIS EN GAGED" 

po si tion.

 

•  Turn ignition key to "OFF" position.

 

• 

Make sure blades and all moving parts 

have completely stopped.

 

•  Disconnect spark plug wire(s) from 

spark plug(s) and place wire where it 

cannot come in contact with plug.

STORAGE

When grass catcher is to be stored for a period of time, 

clean it thoroughly, remove all dirt, grass, leaves, etc. Store 

in a clean, dry place.

CAUTION:  Do not leave grass in bag-

ger containers.  Empty containers after 

each use and before storing.  Failure to 

do so may result in spontaneous com-

 bus tion which could develop into a fire.

CAUTION:  Grass catcher compo-

nents are subject to wear, damage 

and deterioration, which could expose 

moving parts or allow objects to be 

thrown.  Frequently check components 

and replace with manufacturer's re-

commended parts, when necessary.

CUSTOMER RESPONSIBILITIES

Summary of Contents for 532 43 46-60













Reviews: