Weed Eater 532 43 46-60 Owner'S Manual Download

Page: 6 / 12

CONTAINER MOUNTING (See Fig. 4)

1. Install one container to left side first. Install other

container to right side.

NOTE

: Left edge of right con tain er should always over lap

right edge of left con tain er at center sup port.
2. Close cover and lock latch over center support tube.

To lock and release latch, pull back on latch handle.

Fig. 4

CENTER

SUPPORT

TUBE

COVER

LATCH

HANDLE

CONTAINER

HANDLE

Fig. 3

MOUNTING COVER ASSEMBLY TO

SUPPORT ASSEMBLY (See Fig. 3)

NOTE

: For ease of assembly, you may wish to obtain the

as sis tance of another person for mounting cover assembly

to riding mower.
1. Lift and rotate cover to align cover bracket with support

assembly.

2. Slide cover assembly down onto the support assem-

bly.

COVER

ASSEMBLY

SUPPORT

ASSEMBLY

Summary of Contents for 532 43 46-60













Search results

Summary of Contents for 532 43 46-60

Reviews:

Related manuals for 532 43 46-60

Brands by name

Popular brands

Weed Eater 532 43 46-60, Owner'S Manual

Search results

Summary of Contents for 532 43 46-60

Reviews:

Related manuals for 532 43 46-60

Brands by name

Popular brands