background image

LIMITED WARRANTY

The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi-
als and work man ship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or 
replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we fi nd to be defective due 
to materials or workmanship. This Warranty is subject to the following limitations and exclusions.

1.    This warranty does not apply to the engine, other than EHP manufactured transaxle/transmission components, 

battery (except as noted below) or components parts thereof.  Please refer to the applicable manufacturer's 
warranty on these items.

2.   Transportation charges for the movement of any power equipment unit or attachment are the responsibility of 

the pur chaser.  Transportation charges for any parts submitted for replacement under this warranty must be 
paid by the purchaser unless such return is requested by Electrolux Home Products.

3.   Battery Warranty:  On products equipped with a Battery, we will replace, without charge to you, any battery 

which we fi nd to be defective in manufacture, during the fi rst ninety (90) days of ownership. After ninety (90) 
days, we will exchange the Battery, charging you 1/12 of the price of a new Battery for each full month from 
the date of the original sale. Battery must be maintained in accordance with the instructions furnished.

4.   The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the 

date of original purchase.

5.   This Warranty applies only to products which have been properly assembled, adjusted, operated, and main-

 tained in ac cor dance with the instructions furnished. This Warranty does not apply to any product which has 
been subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal 
wear of the product.

6.   Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments, 

stan dard hardware and normal maintenance.

7.    In the event you have a claim under this Warranty, you must return the product to an authorized  service deal-

er.

Should you have any unanswered questions concerning this Warranty, please contact:

giving the model number, serial number and date of purchase of your product and the name and address of the authorized 
dealer from whom it was purchased.

THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WAR RAN -
TIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas 
do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above limi-
tations or exclusions may not apply to you. This Warranty gives you specifi c legal rights, and you may have other rights which 
vary from locale to locale.

This is a limited Warranty within the meaning of that term as defi ned in the Magnuson-Moss Act of 1975.

In Canada contact:

Electrolux Canada Corp.
7075 Ordan Drive
Mississauga, Ontario 
L5T 1K6

Electrolux Home Products, Inc.
Outdoor Products Customer Service Dept.
250 Bobby Jones Expressway
Augusta, GA  30909  USA

Summary of Contents for WET17H42STA













































Reviews: