background image

 17

 

Before any service and adjustments:

 

1.  Make sure the blade and all moving parts have stopped completely. 

2.  Disconnect cable from the sparkplug and place where it cannot come in contact with 

plug. 

CAUTION 

Any modifications unauthorized by manufacturers to the machine will lead to the failure of 

warranty.

 

Do not operate the machine until read and understand all enclosed operator’s manual.

 

CAUTION 

WEIBANG parts have been designed and manufactured to the highest quality demands for 

durability and performance of a commercial operation. Always use original spare parts with the 
logo "WEIBANG" to ensure maximum performance, reliability and service life from your 
WEIBANG machine. 

8.1 ENGINE

 

ENGINE SPEED 

Your engine speed has been preset at the factory. Do not attempt to increase the engine speed, 
as this may result in personal injury. If you believe that the engine is running too fast or too slow, 
take your sod cutter to an authorized service centre for repair and adjustment.

 

THROTTLE CONTROL   

If it becomes necessary to adjust or replace the throttle control, see the adjustment section of 
your engine manual.

 

CARBURETOR 

The carburetor has been preset at the factory and adjustment should not be necessary. However, 
minor adjustment may be required to compensate for differences in fuel, temperature, altitude or 
load.

 

 The air filter must be assembled to the carburetor when running engine. 

 Best carburetor adjustment is obtained when fuel tank is ¼ full. 

 For further information, please see the Adjustment section of your engine manual for further 

instruction. 

Contact your nearest authorized engine service department or your local dealer to 

maintenance engine and consulting warranty issues.   

In case any engine failure during the warranty period, the machine should be sent to 

authorized engine service department for checking but not disassembled by customers, otherwise 
it will lead to the warranty invalid. 

8.2 SOD CUTTER 

● 

For easier access to cleaning the sod cutter, the machine may be tipped on its engine guard 

for NO MORE THAN 2 MINUTES. Engine damage may result from gasoline flowing into the 
crankshaft due to prolonged tipping. Refer to the engine operator's manual and maintenance 
instructions.

 

● 

The sod cutter can be tilted forward in 30 seconds

 by lifting up the handle bar. Engine 

damage may result from gasoline flowing into the engine's cylinder due to prolonged tipping. 
Refer to the engine operator's manual and maintenance instructions.

 

Summary of Contents for WBSC457LC































Reviews: