background image

3

1.

Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual. 

2.

It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.

3.

The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental or institutional setting.

4.

Use the weight bench only on a level surface.
Cover the floor beneath the weight bench for
protection.

5.   Inspect and tighten all parts each time you

use the weight bench. Replace any worn
parts immediately. 

6.   Keep children under 12 and pets away from

the weight bench at all times.

7.  Keep hands and feet away from moving parts.

8.

Always wear athletic shoes for foot protec-
tion while exercising.

9.

Always make sure there is an equal amount
of weight on each side of your barbell.

10. Always move the bench out of the way when

performing squat exercises. 

11. The weight bench is designed to support a

maximum of 560 pounds, including the user,
a barbell and weights. Do not place more
than 310 pounds, including the barbell, on
the weight rests. Do not place more than 150
pounds on the weight carriage. Do not place
more than 150 pounds on the leg lever for
normal use. 

12. Make sure that the cable remains on the pul-

leys at all times. If the cable binds as you are
exercising, stop immediately and make sure
that the cable is on the pulleys.

13. When performing standing exercises, stand

inside the area that is shaded in the drawing.

14. Always set both weight rests at the same

height. 

15. Always exercise with a partner. When you

are performing bench press exercises, squat
exercises or toe raise exercises, your part-
ner should stand behind you to catch the
barbell if you cannot complete a repetition.

16.  If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-
ing down.

17. Always disconnect the lat bar from the

weight bench when performing an exercise
that does not use the lat bar.

18. Always secure the weights with the weight

clips when you have mounted them on the
barbell, leg lever, weight carriage or storage
tubes.

19. When using the pulley station, always place

50 pounds on the storage tubes (on the left
rear upright) to balance the cage.

WARNING: Before beginning this or any exercise program, consult your physician. This is especially
important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. ICON assumes no responsibility for personal injury or property damage
sustained by or through the use of this product. 

To reduce the risk of serious injury, read the following important pre-
cautions before using the weight bench.

WARNING: 

Important Precautions

Summary of Contents for PRO OLC
























Reviews: