background image

WARNING:

Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. SEARS assumes no responsibility for personal injury or property
damage sustained by or through the use of this product. 

3

1.

Read all instructions in this manual before
using the weight bench. 

2.

It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.

3.

Use the weight bench only as described in
this manual. 

4.

Use the weight bench only on a level surface.
Cover the floor beneath the weight bench for
protection.

5.   Inspect and tighten all parts each time you

use the weight bench. Replace any worn
parts immediately. 

6.   Keep children under the age of 12 and pets

away from the weight bench at all times.

7.

Always be sure there is an equal amount of
weight on each side of your barbell (not
included) when you are using it. When
adding or removing weights, always keep
some weight on both ends of the barbell and
prevent the barbell from tipping.

8.

Do not use a barbell that is longer than six
feet with the weight bench.

9.

When you are using the leg lever, place a
barbell with the same amount of weight on
the weight rests to balance the bench.

10.  If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-
ing down.  

11.  Always wear athletic shoes for foot protec-

tion while exercising.

12. The weight bench does not include weights.

The weight bench is designed to support a
maximum of 460 pounds, including the user,
a weight bar, and weights. Do not place more
that 210 pounds, including a weight bar and
weights, on the weight rests. Do not place
more than 130 pounds on the leg lever.

13. Make sure that the adjustment knobs are

inserted completely and tightened into the
uprights before beginning any exercise.

14. When adjusting the position of the seat,

make sure that the adjustment pin is inserted
through both adjustment tubes before begin-
ning any exercise (see page 10).

15.  Keep hands and feet away from moving parts.

16. The weight bench is intended for home use

only. Do not use the weight bench in any
commercial, rental, or institutional setting.

17. Always remove the curl post from the front

leg before performing leg curls with the leg
lever.

18. Always exercise with a partner. When you

are performing bench press exercises, your
partner should stand behind you to catch the
barbell if you cannot complete a repetition.

19. When you put weight on the weight rests,

make sure you put at least ten pounds on the
leg lever to balance the weight bench.

Important Precautions

WARNING: 

To reduce the risk of serious injury, read the following important precau-

tions before using the weight bench.

Summary of Contents for 800 831.150741

















Reviews: