background image

 

- 15 - 

WARRANTY 

5 years 

 
Weidmüller gives a 5 year warranty on this product in accordance with the 
warranty terms as described in the general conditions of sale of the Weidmüller 
company which has sold the products to you. Weidmüller warrants to you that 
such products the defects of which have already existed at the time when the 
risk passed will be repaired by Weidmüller free of charge or that Weidmüller 
will provide a new, functionally equivalent product to replace the defective one. 
Safe where expressly described otherwise in writing in this catalogue/product 
description, Weidmüller gives no warranty or guarantee as to the 
interoperability in specific systems or as to the fitness for any particular 
purpose. To the extent permitted by law, any claims for damages and 
reimbursement of expenses, based on whatever legal reason, including contract 
or tort, shall be excluded. Where not expressly stated otherwise in this warranty, 
the general conditions of purchase and the expressive liability commitments 
therein of the respective Weidmüller company which has sold the products to 
you shall be applicable.

 

 
 
 
 
 
 

 
 
 
 
 

Contact Information 

 

Weidmüller Interface GmbH & Co. KG 

Postfach 3030 

32760 Detmold 

Klingenbergstraße 16 

32758 Detmold 

Germany 

 

Phone +49 (0) 5231 14-0 

Fax +49 (0) 5231 14-2083 

E-Mail info@weidmueller.com 

Internet www.weidmueller.com 

Summary of Contents for IE-SW-PL16M Series
















Reviews: