background image

7

 

2.5 Limited Liability Warranty 

Weintek products include the isolated power supply are covered by a limited liability warranty from 

defects in material and workmanship. This warranty does not apply:   
(a) if, in the judgment of Weintek, the product fails due to damage from shipment, handling, storage, accident 

(natural and man-mad) ;   

(b) If the product fails due to misuse, including but not limit to incorrect set-up and wiring, current leakage 

from machine platform and incorrect input power;   

(c) If the product has been maintained in a manner not conforming to product's instructions or has been 

modified in any way;   

(d) If the serial number has been defaced or removed. 

3.0 Specifications 

 

MT8104iH 

Hardware Specification 

Display 10.4" 

TFT 

Brightness 300 

cd/m

2

 

Color 65,536 

colors 

Contrast Ratio 

500:1 

Resolution (WxH dots) 

800 x 600 

Back light 

LED 

LED life time 

30,000 hr. min. 

Touch panel 

4 wires resistive type 

Touch Accuracy 

Active Area Length(X)±2%, Width(Y)±2%

 

I/O port 

COM1 (RS-232/RS-485 2W/4W), COM2(RS232), COM3(RS-232/RS-485 2W) 

Ethernet port 

(10/100 Base-T) 

Audio YES 
USB Port 

1 USB Host port / 1 USB Client port 

Processor 

32bit RISC 400MHz 

Storage 

128MB flash memory 

DRAM 

64MB DDR2 RAM on board 

SD card slot 

Support SD/SDHC 

RTC 

Built-in (CR2032 3V lithium battery.) 

General Specification 

Input Power 

24±20% VDC 

Power Consumption 

400mA@24VDC 

Isolated Power Supply 

Built-in 

CE/FCC 

Complies with EN55022:2006+A1:2007, Class A, EN61000-3-2: 2006, 

EN61000-3-3:1995+A1:2001+A2:2005 and EN55024:1998+A1:2001+A2:2003 standards

Voltage resistance 

500VAC (1 min.) 

Isolation resistance 

Exceed 50M

Ω

 at 500VDC

 

 

Vibration endurance   

10 to 25 Hz (X,Y,Z direction 2G 30minutes) 

Protection structure 

IP65 front panel (O ring seal) 

Storage temperature 

-20° ~ 60°C (-4° ~ 140°F) 

Operating Temperature 

0~50°C 

(32° ~ 122°F)

 

Operation humidity 

10-90% RH (non –condensing) 

Enclosure Plastic 
Dimensions WxHxD 

286 x 212 x 50mm 

Panel cutout dimension 

259 x 201 mm 

Weight 

Approx. 1.6 kg 

Operating System 

Operating System 

EB8000 V3.4.0 or Newer 

                         www.ipc2u.ru

Summary of Contents for MT-600 Series









Reviews: