Weiser PREMIS Installation And User Manual Download

Page: 4 / 11

Install the exterior assembly

Diameter is 2-1/8" (54 mm)

Diameter is 1-1/2" (38 mm)

2-1/8"

54 mm

1-1/2"

38 mm

“E” is required for installation.
Install “E” on “D”.

“E” is not needed for
installation. Discard “E”.

What is the diameter of the hole in the door?

Install exterior assembly and mounting plate.

Cable goes
underneath
latch.

Rotate torque blade to align

with D-shaped hole.

Route cable
through center
hole, then
push cable into
bottom hole.

Support exterior

assembly during
mounting plate
installation.

Keep parallel to
edge of door

Insert key and test latch.
If latch does not extend
or retract smoothly,
adjust screws (S).

Remove key when finished
and make sure the latch
bolt is fully extended.

Tighten
screws evenly.

4 / 11

USA: 1-800-677-5625 • Canada : 1-800-501-9471
www.weiserlock.com

Locate screws for step 3C and keep them within reach.

Summary of Contents for PREMIS












Search results

Summary of Contents for PREMIS

Reviews:

Related manuals for PREMIS

Brands by name

Popular brands

Weiser PREMIS, Installation And User Manual

Search results

Summary of Contents for PREMIS

Reviews:

Related manuals for PREMIS

Brands by name

Popular brands