Weiser PREMIS Installation And User Manual Download | Manualshive

Page: 5 / 11

background image

K

K

H

H

J

5 / 11

© 2017 Spectrum Brands, Inc.

USA: 1-800-677-5625 • Canada : 1-800-501-9471
www.weiserlock.com

a

a

b

b

d

c

c

Remove battery cover and battery pack from interior assembly.

Connect cables and install interior assembly.

A

B

Make sure
turnpiece is in the
vertical position.

Secure with
screws.

bottom hole

Push turnpiece shaft
onto torque blade.

turnpiece
shaft

torque
blade

vertical

Remove
interior cover.

Remove
battery pack.

Do not install
batteries yet.

U

(2x)

Ensure tight cable
connection.

align

Lay excess cable flat
inside the bottom of
the interior housing.

H

4

Install the interior assembly

«
...
3
4
5
6
7
...
»

Summary of Contents for PREMIS












Reviews:

No comments

Related manuals for PREMIS

Brand: Gainsborough Pages: 2

Contemporary Series

Brand: Gainsborough Pages: 2

Brand: Locknetics Pages: 22

Brand: AIRTEQ Pages: 18

Brand: Siegenia Pages: 16

Brand: eKey Pages: 2

Safelock Series

Brand: Weiser Pages: 2

Brand: hager Pages: 4

OFF VEHICLE COUPLER LOCK

Brand: Bolt Pages: 2

Brand: Mul-t-lock Pages: 48

Brand: Yale Pages: 20

Brand: Hansa Pages: 15

Brand: Rittal Pages: 3

Brand: Richelieu Pages: 9

Timberline CB-280

Brand: COMPX Pages: 1

Timberline CB-242

Brand: COMPX Pages: 1

Timberline CB-245

Brand: COMPX Pages: 1

Brand: ZKTeco Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands