ENGLISH
B2 / B3
(2x)
B1 (2x)
B
Longer screws install
closest to door jamb.
Install strike
A
B
C
12"
305 mm
L
L
Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave
controller, and initiate the Inclusion process at the controller. Refer to your
Z-Wave control system instructions for more information.
Press button “A” on the lock one time to include it in your system. The
controller and lock must remain stationary for a total of 60 seconds during
the Inclusion process.
If Inclusion is unsuccessful, initiate the Exclusion process at the controller,
then press button “A” on the lock one time. Once the lock is fully excluded
from the system, repeat the Inclusion process.
“Inclusion” refers to the process in which the lock is added to a Z-Wave controller.
Button
“A”
Z-Wave
Controller
Perform the Inclusion process
A
C
D
B
N
P (2x)
K
Ensure tight cable connection.
Lay cable
flat against
the interior
housing.
Install interior assembly
A
B
C
M
S
J
R (3x)
If needed, re-key the lock to
work with your existing key.
See the supplied SmartKey
Re-key instructions for more
information.
ball
tip
Keep “S” in a safe place, as you will
need it to access the back panel for
additional programming.
Select models only:
Install the battery cover and re-key the lock
Program the lock
Programming
instructions are
located on the
reverse side of
this document.
9
1"
25 mm
2-1/8"
54 mm
1-1/2"
38 mm
1-3/8" — 1-3/4"*
35 mm — 44 mm*
Check dimensions
Additional door preparation may be
required for doors with 1-1/2" (38 mm)
holes. Consult the drilling instructions at
www.weiserlock.com/doorprep.
*Service kits for 2-1/4"
(57 mm) thick doors are
available through Weiser.
2-3/8" (60 mm)
or
2-3/4" (70 mm)
or
E
F
G
G
2-1/8"
54 mm
1-1/2"
38 mm
Prepare exterior keypad
For doors with 2-1/8" (54 mm) holes
For doors with 1-1/2" (38 mm) holes
A
B
C
D
K
Q (2x)
Q
H
Cable goes
underneath latch
Route cable
through center hole,
then push cable
into side hole.
center hole
side hole
Keep parallel to
edge of door
Tighten
screws
evenly
Insert key and test latch.
If latch does not extend or
retract smoothly, adjust
screws (Q).
Remove key when finished
and make sure the latch
bolt is fully extended.
Install keypad and mounting plate
A
D
B
C
N
M
L
x4
AA
L
Make sure
turnpiece is
in the vertical
position.
Disassemble interior assembly and load battery pack
Ensure correct polarity. For best results,
use new non-rechargeable Alkaline
batteries only.
Do not install
battery pack yet!
Use and programming
instructions are located on the
reverse side of this document.
Required Tools
Additional Tools (depending on application)
Installation Guide
180°
A
B
A / A2
Hold the latch in front of the
door hole, with the latch face
flush against the door edge.
If the latch holes are
centered in the door hole, no
adjustment is required.
Proceed to step 4.
If the latch holes are NOT
centered, adjust latch. See
“Latch Adjustment.”
Latch Adjustment (only if needed)
Adjust the backset of latch (if needed)
A
A2
C (2x)
A
B
C
D
Install latch
For doors with chiseled edge
For doors without chiseled edge
wood
block
1-3/4" (44 mm)
1-3/8" (35 mm)
2-1/4" (57 mm)
2-3/8" (60 mm)
2-3/4" (70 mm)
Edge
Backset
Face
Centerline
If your door requires drilling, cut out the template and place it on the exterior side of the door.
Complete door drilling instructions are available at www.weiserlock.com/doorprep.
Template
Fold
A
B
L
Press and hold
the
Lock button while
installing battery
pack (L).
Hold button until the
latch bolt starts
moving on its own.
This step will teach your lock the orientation of your door
and is crucial to lock operation.
HOLD
latch bolt
Did the latch bolt retract
and extend on its own
when the battery pack
was installed?
Door handing process
was successful!
Proceed to Step 11
after latch bolt stops
moving.
Remove battery pack,
wait 15 seconds, then
attempt the process
again.
YES
NO
Perform door handing process
10
11
12
13
E
F
G
H
K
L
M
N
P
Q
S
R
J
A
A2
B
C
D
B1
B2
B3
Parts in the Box
Latch and Strike
Exterior Assembly
Interior Assembly
A
A2
Determine required latch and extend latch bolt
For doors with chiseled edge
For doors without chiseled edge
Weiser
1-866-863-6584
www.weiserlock.com
3
4
5
6
7
8
1
2
61891 / 01
GED1495
