Welbilt Delfield CV10E, Original Instructions Manual

Part Number: 9294045  07/19 

11

Section 2 

Technical Information

4 - COMMAND INTERFACE SYMBOLS

1 - 

Stand-by button 

- Standby button, if pressed for more 

than 3 seconds it takes the card into standby or switches 

it on again.
2 - 

Positive chilling button

 - Used to select the mode of 

positive chilling.
3 - 

Negative chilling button

- Used to select the mode of 

negative chilling.
4 - 

Chill. LED Temperature

 - LED on means that the chilling 

is via tempurature mode (insert probe)
5 -

 Chilling mode button

 - A button that selects the mode 

of chilling with Time or Temperature (insert prode use); 

the selected mode is represented by ignition of one of the 

two LEDs located on the right and left of the button and 

the are marked with the temperature or time symbol.
6 -

 Chill. LED Time

 - LED on means that the chilling is via 

Time mode
7 - 

Decrease button

 - Parameter or setting value decrease 

buttons (the “-” button allows silencing of the beeper if 

active.)
8 - 

Chilling phase LED

 - Symbol representing the chilling 

phase (it flashes when at that phase.)
9 - 

Storage phase LED

 - Symbol representing the chilling 

phase (it flashes when at that phase.)
10 -

 Ice-cream button

 - The ice-cream button which starts 

the ice-cream cycle. (see section 12).
11-

 HACCP button 

- The HACCP button which starts the 

data reversal cycle onto USB.
12 - 

Ozone button

 - Button that starts the ozone sanitising 

cycle (if any).
13 - 

Defrost button

 - Button that when pressed once starts 

drying with door oper (see section 9), while if pressed for 

at least 3 seconds it starts the hot gas defrost cycle.
14 - 

Status LED

 - RGB on mark lettering. The lettering 

assumes the following colors depending on the following 

relative connected states:

BLUE - Phase of chilling, deep-freezing or storage

ORANGE - Thawing

GREEN/BLUE - Machine on stand by

WHITE - Machine at standstill

RED FLASHING - Serious alarm

FLASHING YELLOW - Non-serious alarm (door opening - 

maintenance)
15 -

 Thawing button

 - Button that when pressed starts the 

defrost cycle
16 - 

Program button

 - Programs recall or storage button

17 - 

Temperature symbol

 - The symbol lights up when a 

cycle is active and the cell temperature (time chilling) or 

product temperature (temperature chilling) is detected. 

In the second case the product probe is shown with the 

highest value. With the cycle in progress press the button 

(12) to display in sequence the values of the insert probe 

1 and 2 and the evaporator sensor probe in flashing mode 

and the display (19) will show the letters in sequence SP1+ 

“probe value”, SP2+”probe value” and SE+”value”.
18 - 

Display temperature 

- Second part of the alphanumeric 

desplay (last 4 digits) for representation of the T° cell or T° 

product and evaporater value.
19 - 

Display time

 - First part of the alphanumeric display 

(first 4 digits) for representation of the time value 

remaining of chilling.
20 - 

Time symbol

 - The symbol lights up when the cycle 

is running; the time remaining will be displayed. If the 

button (5) is pressed the elapsed time will flash for 5 

seconds (both for Time and Temperature chilling).
21 - 

Increase button

 - Parameter or setting value increase 

buttons.
22 - 

Cycles start/stop button

 - start/stop the chilling cycle 

set; with a cycle started, the button remains lit.
23 -

 Negative chilling LED -

 The number of LEDs lit indicates 

the intensity of the negative chilling.
24 - 

Positive chilling LED

 - The number of LEDs lit indicates 

the intensity of the positive chilling.