background image

42 

Part Number STH098 06/19

Detailed Descaling and Sanitizing Procedure 

UDP0080

Ice machine cleaner/descaler is used to remove lime scale 

and mineral deposits. Ice machine sanitizer disinfects and 

removes algae and slime.

Step 1 

Move the toggle switch to Off after ice falls 

from the evaporator at the end of a Harvest cycle. Or, set 

the toggle switch to Off and allow the ice to melt off the 

evaporator.

,

Caution

Never use anything to force ice from the evaporator. 

Damage may result.

Step 2 

Remove all ice from the bin.

n

Warning

Wear rubber gloves and safety goggles (and/or face 

shield) when handling Ice Machine Cleaner/Descaler 

or Sanitizer.

,

Caution

Do not mix Ice Machine Cleaner/Descaler (9405463) 

and Sanitizer (9405653) solutions together. It is a 

violation of Federal law to use these solutions in a 

manner inconsistent with their labeling.

Step 3 

To start a cycle move the toggle switch to Wash. 

Step 4 

Wait until water flows over the evaporator 

(about three minutes) then add the proper amount of 

Manitowoc Ice Machine Cleaner/Descaler to the water 

trough.

Model

Amount of Cleaner/Descaler 

Part Number 9405463

UDP0080

1.5 ounces (45 ml)

Summary of Contents for Manitowoc NEO UDP0080A





















































































































































































Reviews: