WF-205
MST
© Weldclass 2019 | E.&O.E. | Edition 2.1
25
7.1.3
Loading Wire Feeder
1.
Release the Wire Feed Tension Arm (17) by pivoting the Wire Feed Tension Adjustment Lever (16)
towards you from the vertical ‘locked’ position.
2.
Check the wire Drive Roller (18) groove matches the selected MIG wire type and size. The drive
roller will have two different sized grooves; the size of the groove in use is stamped on the side of
the drive roller. For flux cored ‘soft’ wire, such as that used in gasless MIG welding, the drive
roller groove has a serrated profile (known as knurled). For solid core ‘hard’ MIG wire, the drive
roller groove used has a ‘v’ shaped profile. For Aluminum solid core ‘soft’ MIG wire, the drive
roller required has a ‘u’ shaped groove. If necessary, remove and change the drive roller by
unthreading the Drive Roller Retainer Knob (19). Once the correct drive roller (18) is selected and
fitted and the Drive Roller Retainer Knob (19) is secured in place, manually feed the wire through
the Wire Inlet Guide (15), through the drive roller groove and into the Outlet Wire Guide Tube
(20).
3.
Ensuring that the wire is correctly seated in the drive roller groove, replace the Wire Feed Tension
Arm (17) and lock it into place by pivoting the Wire Feed Tension Adjustment Lever (16) back to
the vertical position.
4.
Adjusting wire feed tension. This is accomplished by winding the knob on the Wire Feed Tension
Adjustment Lever (16). Clockwise will increase tension, anticlockwise will decrease drive tension.
TIP!
Ideal tension is as little as possible, while maintaining a consistent wire feed with
no drive roller slippage.
Check all other causes of excess wire feeding friction causing slippage first, such as;
incorrect/worn drive roller, worn/damaged torch consumables, blocked/damaged
torch wire guide liner, before increasing wire feed tension. There is a number scale on
the the Wire Feed Tension Adjustment Lever (16) to indicate the adjustment position.
The higher the number indicated, the higher the tension that is set.
WARNING!
The use of excessive feed tension will cause rapid and premature wear of
the drive roller, the support bearing and the drive motor/gearbox.
5.
Connect the MIG Torch to the MIG torch Euro Connector (4) on the front of the machine. Secure
by firmly hand tightening the threaded collar on the MIG Torch connector clockwise.
6.
Check that the correct matching MIG wire, drive roller (18) and MIG torch tip are fitted.
7.
Connect the machine to suitable mains power using the mains input power lead (22). Switch the
mains power switch (21) to ‘I’ (On) to power up the machine.
8.
Set welding process selector to ‘MIG’ (refer to 4.1)
9.
You are now ready to feed the wire through the torch. With the wire feeder cover open, press the
‘Feed Wire’ button (31) to check that the wire is feeding smoothly through the feeder and into
the torch.
10.
Remove the contact tip from the torch and lay the torch out as straight as possible.
11.
Press the ‘Feed Wire’ button (31) until the wire feeds out through the end of the MIG torch.
12.
Replace the tip on the MIG torch and trim off any excess wire.
Summary of Contents for WeldForce WF-205MST
