background image

 

Enterprise IP Phone                   Using the Advanced Phone Functions

 

Using the Advanced Phone Functions  

 

Account Settings 

Please  refer  to  the  previous  part  “Configuration  and  Registration”  for  the  basic 
Account setting information. The following table lists the instruction of the field about 
the advanced Account Setting.  

Field Name

 

Description 

UDP 

Keep-alive 

Message 

Defines  whether  to  active  the  phone  UDP  Keep-alive 
mechanism. The default is Enabled. 

UDP 

Keep-alive 

Interval

(seconds)

 

This  parameter  specifies  how  often  the  phone  will  send  a 
packet to the SIP server. Default is 30 seconds. 

Login 

Expire

(seconds)

 

This  parameter  specifies  the  time  frequency  that  phone 
refreshes  its  registration.  The  default  interval  is  3600 
seconds. 

Local SIP Port 

Local SIP port. The default value is 5060. 

RPort 

The  parameter  allows  you  configuring  the  proxy  to  send 
responses  back  to  a  particular  address  and  port.  The  default 
is disabled. 

SIP Session Timer 

This  document  defines  an  extension  to  the  Session  Initiation 
Protocol (SIP). This extension allows for a periodic refresh of 
SIP  sessions  through  a  re-INVITE  or  UPDATE  request.  The 
refresh  allows  both  user  agents  and  proxies  to  determine  if 
the SIP session is still active.  

Subscribe 

Period

(seconds)

 

This  parameter  could  set  the  period  of  the  subscription.  The 
default value is 1800. 

DTMF Type 

Select the DTMF type. 

You can only configure these settings via Web interface.  
1)

 

Choose Account. 

2)

 

Select the desired account. 

3)

 

Choose Advanced to do the relating settings. 

Summary of Contents for Well SIP-T28











































































































Reviews: