background image

For  users 

 

- 5 - 

2.2.1.    Mode selections 
 

   

  will be light as standard when you turn on the heat pump. 

    Press the 

  button to enter the Silence mode, the 

  will be light.   

Press the 

  button again to exit and enter the SMART mode.   

 

2.2.2.    Compulsory defrosting 

 

    When  the  heat  pump  is  heating  and  the  compressor  is  working  continuously  for  10 

minutes,  press  both  “

”  and  “

”  buttons  for  5  seconds  to  start  compulsory 

defrosting. (Note: the interval between compulsory defrosting should be more than 30 
minutes.) 

 

    The heating light will be twinkling when heat pump is in compulsory or auto defrosting. 

 

  The  running  process  and  ending  of  compulsory  defrosting  are  the  same  as 

auto-defrosting. 

2.3. Daily maintenance and winterizing 

2.3.1. Daily Maintenance 

  Please don

t forget to cut off power supply of the heat pump

 

 

    Please  clean  the  evaporator  with  household  detergents  or  clean  water,  NEVER  use 

gasoline, thinners or any similar fuel. 

    Check bolts, cables and connections regularly. 

 

2.3.2. Winterizing 
 

In winter season 

when you don’t swim

, please cut off power supply and drain water out 

of  the  heat  pump

When  using  the  heat  pump  under  0

,  make  sure  that  the  water 

pump is always running.

 

 

 

 

 

Important: 

Unscrew  the  water union of  inlet  pipe 

to let the water flow out. 

When the water in machine freezes in 

winter  season,  the  titanium  heat 

exchanger may be damaged. 

Summary of Contents for 34-180139





















Reviews: