Poolen storlek
Mått i cm
torlek
cm
Poolen
Mått
Poolen storlek
Mått i cm
Dike för stöd till mittsektion
för stöd till mittsektion
Di
ll mittsektion
Dike för stöd
on
Dike för stöd till mittse
Dike för stöd till mittsektion
Poolen storlek
Mått i cm
torlek
cm
Poolen
Mått
Poolen storlek
Mått i cm
ldjup 120 cm
Po
m
Pooldjup 12
ldjup 150 cm
Po
m
Pooldjup 15
2. GENERAL GUIDELINES
applying to: round-shaped pools, figure-eight-shaped pools, oval-shaped pools
There are a few important guidelines before you start to assemble your pool:
The most important part of the pool is the foil lining. Swimming pool-foil is a thermoplastic material which expands
under heat and contracts when it gets cold. The lining should be installed at temperatures b 15
°
C and +25
°
C degrees because the foil is most easily handled at these temperatures. At higher temperatures there is danger to
overstretch the foil.
Please note also that soft foil can be very easily damaged by improper handling, so avoid any contact with sharp or
rough objects and do not drag it over concrete or any other floor.
3. Pool location, subsoil
applying to: round-shaped pools, figure-eight-shaped pools, oval-shaped pools
We recommend to choose the pool site in a sunny area, with no
trees around the pool. Pay attention to the wind direction and
try to position the skimmer facing the prevailing winds so that
----
the wind blows the dirt to the skimmer.
When the pool location is found it must be checked whether
Pay attention to
the ground is suitable for the erection of the pool. A filled-up
the wind direction!
ground is not suitable because it requires considerably more ef
forts regarding the foundation (refer to picture item 8). In such
cases you need to ask an expert for professional help. Please
make sure that you do not reach the ground water. We recom-
mend the use of a concrete platform for the erection of your
oval-shaped pool
pool. If there is danger of water flowing down the slope, we recommend to roll up a drainage layer of approx. 20 cm.
The platform should be about 30 cm bigger than the main dimensions of the pool, and of course it should be level.
When it is armoured with a steel mesh, a thickness of 15-20 cm is sufficient. On this ground the pool stands safe, the
brim cannot sink in, and the ground is always smooth for cleaning. Welded wire mesh Q 131, concrete Bn 25. For fi
gure-eight-shaped pools, please make sure to incorporate the delivered steel girder base support into the concrete
platform.
Oval-shaped pools require additional supporting side walls to stabilize the pool walls. Supporting side walls must be
connected to the platform by iron reinforcements (not part of the delivery).
4. SETTING UP THE POOL ON A SLOPE
applying to: round-shaped pools, figure-eight-shaped
pools, oval-shaped pools
The level area for the pool must not be filled-up, but the surface
prepared for the pool should be on solid ground. The slope
must be stayed by a wall or by an embankment. Never use the
wall of the pool to support the slope. You might want to contact
an engineer engaged in statical calculations.
5. PREPARATION OF THE GROUND
Most of the oval-shaped pools / figure-eight-shaped pools can
be erected above ground as well as embedded in the ground.
1. Round-shaped pool/ figure-eight-shaped pool as above-ground pools
2. Round-shaped pool / figure-eight-shaped pool half sunk in, up to 20 cm (possible without back filling with lean
concrete; for more than 20 cm, back filling with lean concrete is required).
3. Round-shaped pool / figure-eight-shaped pool as in-ground pool, with back filling of lean concrete, oval-shaped
pool as in-ground pool.
I
I 1
2
I
r:
\\)-'/7/.'
0 ,\,Y/7//<<:;t,,,
3
round-shaped pool
wrong
3
figure-eight-shaped pool
oval-shaped pool
