21
Do not use the cable for purposes other than those for
which it is intended.
Never carry the unit by the cable. Do
not use the cable to pull the plug out of the socket. Protect
the cable against heat, oil and sharp edges..
Be alert.
Pay attention to what you are doing. Be smart
when using the unit. Do not use the soldering tool if you are
having difficulty concentrating.
Avoid abnormal posture.
Arrange your work station in an
ergonomically correct way. Avoid bad posture when using the
unit, as this can lead to postural problems.
The soldering tool must be operated only in perfect
technical working order.
Safety devices must not be
deactivated.
Faults and defects must be repaired immediately.
Before using the unit / tool, safety devices must be carefully
checked to make sure that they are functioning properly and
in the manner intended. Check that moving parts are func
-
tioning properly and are not sticking, and whether parts are
damaged. All parts must be correctly fitted and must satisfy
all the requirements necessary to guarantee troublefree
operation of the unit.
Use the correct tool.
Use only accessories or auxiliary de
-
vices which are included in the list of accessories or appro-
ved for use by the manufacturer. Use WELLER accessories
or auxiliary devices on original WELLER equipment only. The
use of other tools and other accessories can cause injury.
Secure the tool.
Use clamping fixtures to hold the
workpiece.
Starting up the device
Caution!
Please adhere to the operating instructions of the
connected devices.
Make sure the machine is switched off before plugging in.
After switching on the device, the microprocessor carries out
a self- test and reads out the values of the parameters stored
in the tool.
Check to see if the mains voltage matches
the ratings on the nameplate.
The set-point temperature and fixed temperatures are stored
in the tool. The actual temperature value increases to the
set-point temperature (= soldering tool is heated up).
Desoldering
Carry out soldering work as directed in the operating instruc
-
tions of your connected soldering tool.
Handling the soldering tips
•
Coat the selective and tinnable soldering tip with solder
when heating it up for the first time. This removes oxide
coatings which have formed during storage and impurities
from the soldering tip.
•
Make sure that the soldering tip is well coated with solder
during breaks between soldering work and prior to storage
of the device.
•
Do not use aggressive fluxing agents.
•
Always make sure that the soldering tips are fitted properly.
•
Select as low a working temperature as possible.
•
Select the largest possible soldering tip shape for the
application.
Rule of thumb: the soldering tip should be roughly as large
as the soldering pad.
•
Coat the soldering tip well with solder to ensure that there
is efficient heat transfer between the soldering tip and the
soldering area.
•
Prior to extended breaks between soldering work, switch
off the soldering system or use the Weller function to
reduce the temperature when the soldering equipment is
not in use.
•
Coat the tip with solder prior to storage if you do not intend
to use the soldering iron for an extended period of time.
•
Apply solder directly to the soldering area, not to the
soldering tip.
•
Change the soldering tips using the designated tool.
•
Do not apply mechanical force to the soldering tip.
WARNING
Flammable gases and liquids may not be extracted.
The device may only be used with correctly fitted and
suitable filter cartridges.
Replace filter cartridges when full.
This device may only be used at room temperature and
indoors. Protect against moisture and direct sunlight.
User groups
Due to differing degrees of risk and potential hazards, sever-
al work steps may only be performed by trained experts.
Work step
User groups
Default soldering para-
meters
Specialist personnel with
technical training
Replacing electrical repla-
cement parts
Electricians
Default maintenance
intervals
Safety expert
Operation
Filter change
Non-specialists
Operation
Filter change
Replacing electrical repla-
cement parts
Technical trainees under the
guidance and supervision of a
trained expert
EN
ENGLISH
PK Elektronik Vertriebs GmbH, E-Mail: info@pkelektronik.com, Internet: www.pkelektronik.com
Summary of Contents for T0053452699
Page 11: ...10 i i PK Elektronik Vertriebs GmbH E Mail info pkelektronik com Internet www pkelektronik com...
Page 12: ...11 1 2 PK Elektronik Vertriebs GmbH E Mail info pkelektronik com Internet www pkelektronik com...
Page 15: ...14 PK Elektronik Vertriebs GmbH E Mail info pkelektronik com Internet www pkelektronik com...
