English
Thank you for placing your trust in our company by pur-
chasing the Weller Soldering Station WSD 151.
Production was based on stringent quality requirements
which guarantee the perfect operation of the device.
1. Caution!
Please read these Operating Instructions and the atta-
ched safety information carefully prior to initial operation.
Failure to observe the safety regulations results in a risk
to life and limb.
The manufacturer shall not be liable for damage resulting
from misuse of the machine or unauthorised alterations.
The Weller Soldering Station WSD 151 corresponds to
the EC Declaration of Conformity in accordance with the
basic safety requirements of Directives 89/336/EEC and
73/23EEC.
2. Description
2.1 Control unit
The soldering station WSD 151 was specially developed
for soldering tasks with an extremely high heat require-
ment. The 150 W heater power combined with the optimal
transfer of heat to the soldering iron bit guarantees the
high performance capability of the WSP 150 soldering
iron. As an alternative to the WSP 150, all the soldering
tools listed in the list of accessories can be connected to
the unit. A microprocessor makes operation simple and
comfortable. The digital electronic control system guaran-
tees the best possible control performance for various
soldering tools. The soldering tools themselves are recog-
nized automatically by the soldering station and assigned
the corresponding control parameters. The high-powered
24 V heating elements make excellent dynamic perfor-
mance possible, so that the soldering tools can be used
universally.
Various equipotential bonding possibilities for the solde-
ring iron tip, zero power switch and antistatic design of
control unit and iron complete the high quality standard.
The possibility of connecting an external input unit further
increases the variety of functions of this soldering station.
With the optional input units WCB 1 and WCB 2 it is pos-
sible to implement time functions, locking functions, etc.
Integrated temperature gauge and PC interface are inclu-
ded in the extended scope of the input unit WCB 2.
The temperature for the WSP 150 soldering iron can be
set over the range from 50°C - 550°C via 2 buttons
(Up/Down). The adjustment range is automatically limited
to 450°C if a different soldering tool is connected. The set-
point and actual value are displayed digitally. A blinking
red LED in the display signals that the preset temperatu-
rehas been reached – this serves as a optical regulator.
Constant illumination means that the system is heating
up.
2.2 Soldering irons
LR 21:
Our "standard” soldering iron. With a
power of 50 watts and a wide
spectrum of soldering tips (ET series) this
soldering iron can be
used anywhere in the electronics sector.
LR 82:
High-performance 80 watt soldering iron
for soldering work with high heat require
ments. The soldering tip is attached by a
bayonet catch to ensure correct position
when using different tips.
WSP 80:
The soldering iron WSP 80 is characteri
zed by its capacity for reaching the solde
ring temperature quickly and precisely. Its
slim design and heating power of 80
watts makes universal usage possible -
from extremely fine to high-temperature
soldering work. Work can be continued
immediately after switching soldering tips
13
Technical Data
Dimensions in mm:
166 x 115 x 101 (l x w x h)
Supply voltage (8):
230 V / 50/60 Hz
240 V/120 V / 50/60 Hz (dual version)
100 V / 50/60 Hz
Power input:
150 W
Class:
1 (control unit) and 3 (soldering iron)
Fuse (9):
230 V; T800mA
240 V/120 V; T1,6A
100 V; T1,6A
Temp. control:
50°C - 550°C
Precision:
± 11°C
Equipotential bonding (6):
Via a 3.5 mm jack bush (initial state-hard-grounded)
Summary of Contents for WSD 151
Page 2: ......
Page 7: ...7 WSD 151 ...
Page 68: ...61 Circuit Diagram ...
Page 69: ...62 Explo Drawing ...
