19
Read these instructions and the safety guidelines carefully before
starting up the unit and starting work.
Please adhere to the operating instructions of the connected devices.
Installation and commissioning of the machines which we have supplied may
only be performed by authorized specialist personnel.
Failure to observe the safety regulations results in a risk to life and limb.
Keep these instructions in a place that is accessible to all users.
Safety information
The soldering tool must be operated only in perfect technical working order.
Safety devices must not be deactivated.
Faults and defects must be repaired immediately.
Before using the unit / tool,
safety devices must be carefully checked to make sure that they are functioning
properly and in the manner intended. Check that moving parts are functioning
properly and are not sticking, and whether parts are damaged. All parts must
be correctly fitted and must satisfy all the requirements necessary to guarantee
troublefree operation of the unit.
For safety reasons, children and youths under the age of 16, as well as persons
who are not familiar with these operating instructions, may not use the device.
Children shall not play with the appliance.
This device is not intended for use by persons (including children) with limited
physical, sensory or mental aptitude, or by persons who lack knowledge or
experience in handling the device.
Keep other persons well away from your workplace.
The work area is out of bounds for children and unauthorised persons. Never allow
other persons to touch the soldering tool or cable.
WARNING
Danger of injury
The device or parts of the device may fall off during transportation.
WARNING
Danger of injury
Danger of crushing injuries! / Cutting hazard
Risk of injury after opening the hood, as no protection against moving parts is
provided.
•
The key-operated switch may only be used by specialist, trained personnel, who are
fully aware of the risks involved in operating the machine without any protective
function, thanks to their specialist qualification and experience.
•
The key must be kept in a safe place.
•
Do not leave the key in the switch during normal operation of the machine!
Risk of injury on interchangeable magazines
•
Never put your hand inside the device when the magazine is open
Danger: compressed air.
•
Take care when fitting the compressed air connection. Depressurise the hose.
When soldering, hold the coupling firmly as the coupling socket can spring out of
your hand.
WARNING
Electrical shock
Protect yourself against electric shocks.
•
Do not use the soldering tool in a damp or wet environment.
•
Before doing any work on the machine, pull the plug out of the socket. Leave the
unit to cool down.
Connecting the control unit incorrectly poses a risk of injury due to electric
shock and can damage the device.
•
Carefully read the attached safety information, the safety information accompanying
these operating instructions as well as the operating instructions for your control
unit before putting the control unit into operation and observe the safety precautions
specified therein.
•
Only connect WELLER tools.
If the device is faulty, active electrical conductors may be bare or the PE
conductor may not be functional.
•
Repairs must always be referred to a Weller-trained specialist.
•
If the electrical tool‘s power supply cord is damaged, it must be replaced with a
specially prefabricated power supply cord available through the customer service
organisation.
WARNING
Fire hazard
•
Keep all combustible objects, liquids or gases well away from the hot soldering tool.
•
Once switched on, never leave the tool unattended.
WARNING
Risk of burns
The soldering tip becomes very hot during soldering work. There is a risk of
burns from touching the tips. Tools may still be hot long after they have been
switched off.
•
Do not touch the hot tools and workpieces.
•
Only replace solder tips when cold
•
Do not touch the housing until it has cooled down.
After the soldering process, the soldering tool and the workpiece holder are
still hot.
•
Soldering profiles must be configured so that the printed circuit boards are cold on
removal.
•
Wear gloves when removing the printed circuit boards. Care must be taken to
ensure that hot printed circuit boards are beyond the reach of third parties after
removal.
WARNING
Danger of poisoning
•
The soldering process can produce hazardous solder vapours. Hazardous vapours
and other aerosols may be released when printed circuit boards are heated and/or
overheated.Use a solder fume extraction unit.
•
When working with adhesives, special attention must be paid to the warning
information provided by the adhesive manufacturer.
•
Avoid skin contact with the adhesive or the solder paste. Skin contact with these
substances can have adverse health effects.
The power cable must only be plugged into the power socket or adapter
approved for this purpose.
Check to see if the mains voltage matches the ratings
on the nameplate. Make sure the machine is switched off before plugging in.
Do not use the cable for purposes other than those for which it is intended.
Never carry the unit by the cable. Do not use the cable to pull the plug out of the
socket. Protect the cable against heat, oil and sharp edges..
Be alert.
Pay attention to what you are doing. Be smart when using the unit. Do not
use the soldering tool if you are having difficulty concentrating.
Avoid abnormal posture.
Arrange your work station in an ergonomically correct way.
Avoid bad posture when using the unit, as this can lead to postural problems.
Use the correct tool.
Use only accessories or auxiliary devices which are included
in the list of accessories or approved for use by the manufacturer. Use WELLER
accessories or auxiliary devices on original WELLER equipment only. The use of
other tools and other accessories can cause injury.
Store your soldering tool in a safe place.
When not in use, units and tools should
be stored in a dry, high or locked area out of the reach of children. Make sure that
unused soldering tools are free of voltage and de-pressurised.
Fix the axles in place during transport using cable ties.
Specified Conditions Of Use
The soldering installation may only be used to piston solder assemblies.
This device may only be used at room temperature and indoors. Protect against mois-
ture and direct sunlight.
User groups
Due to differing degrees of risk and potential hazards, several work steps may only be
performed by trained experts.
Work step
User groups
Operation
Machine operation, Fault clearance,
Equipment
Non-specialists (semi-skilled, experienced)
Technical trainees under the guidance and
supervision of a trained expert
Installation., Starting up the
device, Cleaning, Maintenance,
Maintenance, Working on
pneumatic equipment
Specialist personnel with technical training
Working on electrical equipment
Electricians
Technical trainees under the guidance and
supervision of a trained expert
Default maintenance intervals
Safety expert
EN
ENGLISH
Summary of Contents for WTBR 1000
