background image

MAINTENANCE INSTRUCTIONS 

11 

CARE OF STAINLESS STEEL 

 

Stainless steel is a marvelous material:  strong, lustrous and low maintenance. With a 
minimum of care, it will normally retain its beauty and durability for the life of  the     
equipment.  In some applications, however, special care is required in order to maintain 
stainless steel’s special properties. 

 
External components, such as cabinets and control panels, are finished with a grain  
pattern. This pleasing finish is best maintained by cleaning with a non-abrasive      
cleanser applied with a soft cloth.  Rub only in the direction of the grain.  In the absence 
of visible grain, rub only along the longest axis of the appliance. 

 
Restore stainless steel’s luster by applying a polish specifically made for stainless steel.  
Spray on, wipe off with a soft cloth, rubbing in the direction of the grain. 
 
 

Never use metal implements, wire brushes, abrasive scratch pads or steel 

 

wool to clean stainless steel.

 

 
Warmer pans, insets and other vessels are subject to a harsher environment.  Wells 
Manufacturing uses an very high quality stainless steel (#304DDQ) for our food warmer 
pans.  Even the highest quality stainless steel, however, is mostly iron, and will rust, pit 
and corrode under the following conditions: 

 

• 

Poor Water Quality:  

Hard water (water with a high content of dissolved minerals) 

will leave mineral deposits when allowed to dry.  Calcium (lime) can buildup on 
heated surfaces, even under water.  If left unattended, hard water spots and lime 
buildup can lead to rusting, corrosion and pitting. 

• 

Contact with Chlorides:  

Chlorides (specific compounds of chlorine) are found in 

food, table salt and many cleansers.  Chlorides can attack the surface of stainless 
steel, resulting in corrosion and pitting.

 

 
 

Keep your stainless steel warmers clean and free from calcium buildup. 

 

Use alkaline, alkaline chlorinated or non-chloride cleanser.   

 

Use citric acid-based cleaners to remove calcium deposits. 

 
For additional information, please read the NAFEM Stainless Steel Equipment and 
Cleaning Guide.  Contact NAFEM at : 
 

North American Association of Food Equipment Manufacturers 

 

401 N. Michigan Avenue 

 

Chicago, Illinois  60611-4267 

 (312) 

644-6610 

 

M

011C.03  2M

-308019 

  Owne

rs M

anual fo

r B

u

ilt-

In

 Three

-W

e

ll M

odular T’

Stat 

W

a

rme

rs 

Summary of Contents for MOD-300T





















Reviews: