background image

6

HEATING OPTIONS

1.  Moist heat with Humitrol Rack:

 

a.  MOIST operation prevents food from drying out as heat is      

applied to the warming chamber.

 

b.  To set for MOIST operation, remove the Humitrol Rack from  

bottom of drawer insert pan and   carefully pour approximately    

2 quarts of water (½” depth) into the pan.  Reinstall rack.

 

c.  When the drawer is closed, the Humitrol Rack allows water   

vapor to rise through the stored product in the drawer. The    

Humitrol Rack also decreases the sloshing effect of the water  

in the pan when the drawer is opened.  

 

d.  Place the food directly on the rack.  The rack is designed to   

support the food off of the steam vents, where water droplets  

may form.

 

e.  Check the water level in the pan periodically, and add water  

when necessary.

 

f.  Set the front air vent between fully closed and half-open.        

Actual setting will depend upon the type and amount of product  

stored in the drawer, the temperature setting, and the            

frequency with which  the drawer is opened.

2.  Moist heat with pans:
 

a.  This Wells warmer is designed to accommodate any             

combination of standard-size, steam table pans.

 

b.  Place a small amount of water in drawer pan.  Place the steam  

table pans in the drawer pan.

 

c.  Check the water level in the pan periodically, and add water  

when necessary.

3.  Dry heat:
 

a.  For some applications, you may want to store previously       

prepared foods in a dry-heat environment.  To do so, place the  

food directly into the empty (i.e. no water) drawer pan.

OPERATION

CAUTION:

HOT SURFACE

Exposed surfaces can be hot 

to the touch and may cause 

burns.

NOTE:  

The chart below is intended 

as a guide ONLY.  Your 

own experience with this 

appliance, type of foods 

and method of operation will      

enable you to determine the 

temperature control and air

vent settings best suited to 

your operation.

HEATING

INDICATOR

THERMOSTATIC

TEMPERATURE

CONTROL

IL2930

OPERATING CHART FOR DRAWER WARMERS

  PRODUCT TYPE

RECOMMENDED  

STORAGE TEMP.

TYPE OF HEAT

CONTROL 

SETTINGS

AIR VENT 

SETTINGS

  Hard Rolls

160-185ºF

71-85°C

Dry  

7-8

Full Open

  Soft Rolls

150-175ºF

65-79°C

Moist  

6-7

Open - ½

  Vegetables

175-185ºF

79-85°C

Moist

7-8

Open - ½

  Meats

165-185ºF

74-85°C

Dry

6-8

Full Open

  Fish

165-185ºF

74-85°C

Moist

6-8

Closed

  Casseroles

150-175ºF

65-79°C

Dry

6-7

Full Open

  Pies, Desserts

160-185ºF

65-85°C

Dry

6-7

Full Open

  Taco Shells

150-170ºF

65-76°C

do not put water  

in the pan

4-6

Full Open

  Corn Chips

150-170ºF

65-76°C

4-6

Full Open

Summary of Contents for RW-1HD thru RW-3HD Heavy-Duty





















Reviews: