background image

Symbols on the product

Be careful and use the product correctly.

This product can cause serious injury or

death to the operator or others.

Read the operator's manual carefully and

make sure that you understand the

instructions before you use this product.

Use a protective helmet in locations where

objects can fall on you. Use approved

hearing protection. Use approved eye

protection.

Use approved protective gloves.

Use heavy-duty slip-resistant boots.

The product can cause objects to eject,

which can cause injury.

Maximum speed of the output shaft.

50FT

15 m

50FT

15 m

Keep a minimum of 15 m distance to

persons and animals during operation of the

product.

Hex Wrench Screwdriver 

Wrench

Spacer

Catcher 

Allen Key 

Tools Bag 

Tools

 

bag

 

Choke 

off

 

Fuel.

03

Product liability

As referred to in the product liability laws, we are not

liable for damages that our product causes if:
• the product is incorrectly repaired.
• the product is repaired with parts that are not from

the manufacturer or not approved by the

manufacturer.

• the product has an accessory that is not from the

manufacturer or not approved by the manufacturer.

• the product is not repaired at an approved service

center or by an approved authority.

Choke 

on

Air

 Primer Bulb

Summary of Contents for WS-ST42G






















Reviews: