background image

WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with 

this commitment and our dedication to quality.

LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE

GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer 

power tools will be free from defects in material or workmanship for a period of two (2) years from date of 

purchase. Ninety days for all WEN products if the tool is used for professional or commercial use.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty and, to the extent 

permitted by law, any warranty or condition implied by law, shall be the repair or replacement of parts, with-

out charge, which are defective in material or workmanship and which have not been misused, carelessly 

handled, or misrepaired by persons other than Seller or Authorized Service Center. To make a claim under this 

Limited Warranty, you must make sure to keep a copy of your proof of purchase that clearly defines the Date 

of Purchase (month and year) and the Place of Purchase. Place of purchase must be a direct vendor of Great 

Lakes Technologies, LLC. Third party vendors such as garage sales, pawn shops, resale shops, or any other 

secondhand merchant void the warranty included with this product. Contact techsupport@wenproducts.com 

or 1-800-232-1195 to make arrangements for repairs and transportation. 

When returning a product for warranty service, the shipping charges must be prepaid by the purchaser. The 

product must be shipped in its original container (or an equivalent), properly packed to withstand the hazards 

of shipment. The product must be fully insured with a copy of the warranty card and/or the proof of purchase 

enclosed. There must also be a description of the problem in order to help our repairs department diagnose 

and fix the issue. Repairs will be made and the product will be returned and shipped back to the purchaser 

at no charge.

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS THAT WEAR OUT FROM REGULAR USAGE 

OVER TIME  INCLUDING  BELTS,  BRUSHES,  BLADES,  ETC. ANY  IMPLIED WARRANTIES  SHALL  BE  LIMITED  IN 

DURATION TO TWO (2) YEARS FROM DATE OF PURCHASE. SOME STATES IN THE U.S., SOME CANADIAN PROV-

INCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITA-

TION MAY NOT APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING 

BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. 

SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION 

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY 

TO YOU.

THIS  LIMITED WARRANTY  GIVES YOU  SPECIFIC  LEGAL  RIGHTS, AND YOU  MAY ALSO  HAVE  OTHER  RIGHTS 

WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA AND FROM COUNTRY 

TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PORTABLE ELECTRIC TOOLS, BENCH POWER TOOLS, OUTDOOR 

POWER EQUIPMENT AND PNEUMATIC TOOLS SOLD WITHIN THE UNITED STATES OF AMERICA, CANADA AND 

THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT 

THE WEN CUSTOMER SUPPORT LINE.

WARRANTY STATEMENT

THANKS FOR REMEMBERING

20

Summary of Contents for AT6535





















Reviews: