manualshive.com logo in svg

Wenger Signature Choral Riser 4-Step, Assembly & Owners Manual

The Wenger Signature Choral Riser 4-Step is a versatile and sturdy platform for choirs and performers. Easily assemble with the included Assembly & Owners Manual for a seamless setup. Download the manual for free from 88.208.23.73:8080 to ensure smooth and efficient use of your choral riser. Elevate your performances with ease.

Share
Download
background image

11

B

ACK

R

AIL

A

SSEMBLY

CONTINUED

11. Locate the three Horizontal Tubes. 

Remove and discard the protective rubber 

caps from the threaded studs.

12. Insert the threaded studs of the Horizontal Tubes 

through the pre-drilled holes in the front side of 

the Upright Tubes. 

Secure them with six 3/8” Jam Lock Nuts and 

tighten securely.

A

SSEMBLY

CONTINUED

Jam

Lock

Nuts

Horizontal

Tubes

Completed Back Rail

and Chassis

Assembly

The Back Rail Assembly must

remain attached at all times.

Removal can cause riser

instability and could result in

injury.

!

WARNING

Summary of Contents for Signature Choral Riser 4-Step

















Reviews:

No comments

Related manuals for Signature Choral Riser 4-Step

SAYFA KATT LD429T Quick Start Manual preview
KATT LD429T
Brand: SAYFA Pages: 8
Cosco 13 Ft Type IA Operation And Safety Instructions preview
13 Ft Type IA
Brand: Cosco Pages: 16

Brands by name

Popular brands

Load more brands