English
ENG
ORIGINAL INSTRUCTIONS
4
and/or battery before making any adjustments,
changing accessories or storing the power tool.
Such preventive safety measures reduce the risk
of starting the power tool accidentally. Do not use
accessories which are not specifically designed
and recommended by Werku
®
. Just because the
accessory can be attached to this power tool, it
does not assure safe operation. The rated speed
of the accessory must be at least equal to the
maximum speed marked on this power tool.
Accessories running faster than their rated speed
can break and fly apart. The outside diameter and
the thickness of your accessory must be within
the capacity rating of this power tool. Incorrectly
sized accessories cannot be adequately guarded
or controlled. Threaded mounting of accessories
must match the spindle thread. For accessories
mounted by flanges, the arbour hole of the
accessory must fit the locating diameter of the
flange. Accessories that do not match the mounting
hardware of this power tool will run out of balance,
vibrate excessively and may cause loss of control.
Do not use a damaged accessory. Before each
use, inspect the accessory. If this power tool or
its accessory is dropped, inspect for damage or
install an undamaged accessory. After inspecting
and installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run this power tool at maximum no-
load speed for one minute. Damaged accessories
will normally break apart during this test time.
Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the
spinning accessory. Regularly clean this power
tool’s air vents. The motor’s fan will draw the dust
inside the housing and excessive accumulation of
powdered metal may cause electrical hazards.
STORE POWER TOOLS.
Store power tools out of reach of children and
not allow the handling of power tools to people
unfamiliar with the tools or these instructions.
Power tools are dangerous in the hands of
untrained users.
MAINTENANCE.
Check moving parts for misalignment or binding,
there are no broken parts or other conditions that
may affect the operation of power tools. Power tools
are repaired before use when they are damaged.
Many accidents are caused by poorly maintained
power tools. Use power tools, accessories and
tool tips, etc. according to these instructions and
in the manner provided for the particular type of
power tool, taking into account the conditions work
and work to develop. The use of the power tool for
applications other than those intended could result
in a dangerous situation. Please check your power
tool serviced by a Werku
®
official repair service
using only identical replacement parts. This will
ensure the safety of the power tool is maintained.
CHECK CONDITION.
Make sure that all the screws in the sander are
perfectly tightened. In cold climates or when the
sander has not been used for a period, allow the
sander to warm up by leaving it to run empty for a
few minutes, to ensure that all internal components
are perfectly lubricated. Make sure that the possible
installed accessories are perfectly fitted in place.
BEFORE STARTING WORK.
Make sure that the sander is firmly supported
before using. Check that no one is standing
beneath you when using the sander in high areas.
Keep your hands away from all moving parts of
the sander.
DURING THE OPERATION.
Do not leave the sander operating without having
it firmly fixed. Only turn it on when you are sure
you have full control over it. Do not point the
sander at anyone while in use. When operating
the sander will produce vibrations. The screws
may gradually come loose, and possibly cause
faults or accidents. Keep your hands away from
all moving parts of the sander.
AT FINISH WORKING.
Do not touch the possible accessories installed
in the sander after use. It may be hot and cause
burns. Some materials worked with may contain
chemicals or toxic components. Avoid inhaling
these substances or allowing them to come into
contact with your skin. Use PPE designed to
prevent and protect against incidents of this kind.
OTHER SAFETY INSTRUCTIONS.
1) Maintain a firm grip on this power tool and
position your body and arm to allow you to resist
kickback forces. Always use auxiliary handle,
