WERKU WK501000, Original Instructions Manual

English

ENG 

ORIGINAL INSTRUCTIONS

5

ce and spray evenly from left to right and up and down 

with slow movements.

Do not spray at an angle, as 

this will cause the paint to form droplets on the surfa-

ce.

When spraying large areas, use a correct working 

plan (11).

Spray moving the arms and not the wrist.

Control the speed of the paint spray gun to achieve 

a smooth, regular movement.

Moving too quickly will 

cause the paint layer to be too thin.

Similarly, moving 

too slowly will cause the paint layer to be too thick.

Apply the coats of paint one by one, leaving them to 

dry for the times indicated by the manufacturer.

NEEDLE, NOZZLE AND REGULATOR CHANGE.

Unscrew and remove the spray direction control (A). 

Unscrew and remove the nozzle regulator (E). Subse-

quently, pull back the fluid-flow needle until it is comple

-

tely removed. Using the wrench provided, unscrew and 

remove the fluid-flow nozzle from the head, then screw 

in the new fluid-flow nozzle. Insert the new fluid-flow 

needle. Then screw in the nozzle regulator (E). Screw 

in the new spray direction control (A).

IMPORTANT.

Using products containing halogenated hydrocar-

bons may cause chemical reactions that lead to 

explosions.

When using solvents and detergents 

containing halogenated hydrocarbons, such as 

1,1,1-trichloroethane and methylene chlorate, 

chemical reactions may occur in the tank, gun and 

galvanised parts (when 1, 1, 1-trichloroethane co-

mes into contact with water droplets it produces 

chlorohydric acid).

We recommend using products 

that do not contain these elements.

Before using 

the paint spray gun and its accessories, these 

must be cleaned with cleaning solvent, to remove 

the protective film applied before packing.

Acid or 

alkaline products must not be used to clean the 

paint spray gun.

MAINTENANCE.

Drain all condensation from the air compressed 

tanks and hoses (12). To do so, open the decom-

pression taps and other drainage valves in the 

tanks.

IMPORTANT.

The paint spray gun has been designed for a long 

working life with minimum maintenance.

Optimum 

use depends on correct care of the paint spray gun 

and regular cleaning.

The paint spray gun may be 

cleaned effectively using compressed air.

If com-

pressed air is not available, use a brush to remo-

ve dust from the paint spray gun.

Cetain cleaning 

agents and solvents damage plastic parts, among 

them are gasoline, carbon tetrachloride, chlorina-

ted cleaning solvents, ammonia and household 

cleaners containing ammonia.

Do not use any of 

these to clean the paint spray gun.

ENVIRONMENT PROTECTION.

The materials and components that have been 

used to manufacture this product can be re-used 

and recycled.

Werku

®

 is adhered to an Integrated 

Management System that is in charge of the co-

rrect elimination of the residues of this product..

Do not eliminate this product with domestic resi-

dues.

Werku

®

 offers to its clients a free collection 

service of these residues through any of its sale 

points, or in the collection points established by 

the Integrated Management System or in the re-

cycling point of your locality.

WARRANTY AND TECHNICAL SERVICE.

Werku

®

  offers  a  warranty  that  covers  the  repair 

of all defects found due to faults in the materials 

or manufacture. For this cover to be effective it is 

necessary for these defects to appear within the 

validity period. The consumer is entitled to free 

repair of all defects (shipping costs, labour costs 

and materials included), either via the repair or by 

replacement (if necessary, with a later model). In 

any case, Werku

®

 will not accept replacements if 

these represent a disproportionate cost compared 

to the cost of repair. This warranty does not affect 

consumer’s rights established by European or 

national laws. The validity period of this warranty 

is 3 years. The validity period starts on the date of 

purchase by the first consumer. This date is shown 

on the invoice or receipt of purchase. Any claims 

arising from this warranty must be presented to 

the Werku

®

 distributor or the Werku

®

 Technical 

Assistance Service. To do so you must present 

this warranty correctly completed and stamped by 

the distributor, together with the sales invoice or 

receipt. To require any information in relation to this 

warranty, the buyer and/or distributor may contact the 

Technical Assistance Service by telephone on +34 

981 648 119, or by e-mail at info@werku.com. This 

warranty does not cover defects caused by parts that