6
2. Opening / Extending and
Deploying the Ladder
2.1 Before using the ladder it shall be checked that all
locking mechanisms are working properly. If the
mechanism is not working properly, do not use the
ladder.
2.2 Stand and support the closed / retracted product
vertically and upon a firm / level surface and then place
one foot centrally upon the fixed bottom rung (rung 1)
to stabilise the ladder (see figure 3).
2.3 Note that the ladder must be opened /
extended from the lowest extendable section
and not from either a middle or the top section.
2.4 Using both hands, lightly hold the stile tubes
below the black support rings of rung 3 (the
rung of the first / lowest extendable ladder
section) and then pull up and fully extend the
section (see figure 3).
2.5 Repeat step 2.4 and extend each further
ladder section (one at a time) until the desired
ladder length is reached (note that it will eventually
become necessary to lower the extended ladder to
enable higher ladder sections to be extended).
2.6 Check all ladder lock indicators (immediately below
each extended section) are showing ‘full green’ (see
figure 2).
2.7 Note the slope of the ladder feet and the location of the
safety grip wall bumper square pads and then correctly
deploy and support the extended ladder forwards and
at an angle of 75 degrees to the horizontal (see figures
4 and 5).
2.8 Ensure that the deployed ladder is secure by placing
the ladder feet upon a firm and level surface and both
safety grip wall bumper pads against a firm vertical
surface (e.g. a wall). Whenever possible, secure / tie
the top of the extended ladder.
2.9 Take special care in adverse weather conditions (e.g.
strong winds). If in doubt, do not risk your personal
safety and postpone the use of the ladder.
3. Closing / Retracting the Ladder
3.1 Stand and support the open / extended product upright
by firmly holding one of the stile tubes part way up the
ladder with one hand and then using your
other hand, fully depress and then release both ladder
lock release buttons (see figure 6) to unlock the lowest
extended ladder section (note that the ladder sections
will not descend / self -close when these buttons are
depressed).
3.2 Using both hands, lightly hold the outside stile tubes
of the ladder and carefully / slowly pull down all ladder
sections (note that the lowest extended section will
sequentially fully retract / close first which will then
automatically unlock the next extended section).
3.3 Whenever partly reducing the length of the extended
ladder, always follow steps 3.1 and 3.2 first to fully
retract / close the ladder and then follow steps 2.1
to 2.6 to re-extend the ladder to the desired reduced
length.
4. Handling, Storage and Maintenance
4.1 This ladder is a precision built product and
should be handled with care, stored in suitable
conditions and maintained in full working order to
continue providing safe and reliable service.
4.2 Transport the ladder fully closed and hand carry under
arm. With one hand hold the underside of the ladder
lock release housing on the underside of rung 2 (see
figure 1), support / carry the product with your arm
straight and steady the ladder with your other hand.
4.3 Open and close the ladder in a slow and careful manner.
4.4 Avoid striking the product against another object. If
a stile tube is dented or damaged the ladder may be
difficult to operate or may completely malfunction.
4.5 Store the ladder fully closed and vertical,
stood upon both its feet and leant against a vertical
surface.
4.6 Always store the ladder indoors. Damp conditions
could adversely affect the condition and operation of
the product.
4.7 Keep the ladder clean. Wipe the stile tubes occasionally
with a clean, dry cloth. Wipe
and dry the product immediately following exposure
to wet conditions (e.g. rain). Paint or other ‘foreign’
material will impede the telescoping action and must be
cleaned off immediately.
4.8 If any stiffness in the telescoping action develops,
firstly wipe the stile tubes with a clean, dry cloth, then
apply a small amount of silicone spray and wipe any
excess off with a clean cloth.
4.9 Replace worn (or damaged) ladder feet and safety grip
wall bumpers before they are worn smooth. Only
use genuine original replacement parts to ensure your
safety.
4.10 Except to replace ladder feet and safety grip wall
bumpers, do not attempt to disassemble or repair the
product yourself. All repairs and other maintenance
shall only be carried out by a competent person in
accordance with the manufacturer’s instructions. For
any assistance relating to this product contact the
Customer Helpline on 01621 745 900.
4.11 For Professional users; regular periodic inspection of
the ladder is required.
PN115159-01_IM_TelescopicLadder_Rev1018_PRINT.indd 7
10/18/18 5:03 PM