background image

7

•  To hire an authorized service technician to 

assemble this product, call 1-800-445-2480.

•  Assembly requires two persons.

•  Place all parts in a cleared area and remove the 

packing materials. Do not dispose of the packing 

materials until you fi nish assembly.

•  Left parts are marked “L” or “Left” and right parts 

are marked “R” or “Right.”

•  To identify small parts, see page 6.

•  In addition to the included tool(s), assembly 

requires the following tools:

one Phillips screwdriver 

one adjustable wrench 

one pair of pliers 

 

one rubber mallet 

 

Assembly may be easier if you have a set of 

wrenches. To avoid damaging parts, do not use 

power tools.

ASSEMBLY

1. 

 Go to www.wesloservice.com/registration on 

your computer and register your product.

  •   activates your warranty
  •   saves you time if you ever need to contact 

Customer Care

  •   allows us to notify you of upgrades and offers

   Note: If you do not have Internet access, call 

Customer Care (see the front cover of this 

manual) and register your product.

1

2

2.  Identify the Rear Stabilizer (36), which has 

Leveling Caps (37). 

  Attach the Rear Stabilizer (36) to the Frame (16) 

with two M8 x 65mm Carriage Bolts (57), two 

M8 Curved Washers (14), and two M8 Acorn 

Nuts (59); 

start both Carriage Bolts, and then 

tighten the Acorn Nuts.

 

36

37

37

14

14

59

59

57

16

Summary of Contents for momentum G 3.4

























Reviews: