WMarine10 – Technical Manual
Rev. 1.0
28-12-2011
11
Visualizations
Day/night status
Only disp layed in the configuratio n scre ens
Lo w bat tery prot ection
Load turning o n
It ind icates which charg e
prog ram is cu rrently se t
It disp lays internal measur es
Vo ltage level inside the batter y
Indication of curr ent
absor ption on the load
I ndicat ion o f cur rent
ab so rption from the PV
mo dule
Main page.
It displays the battery voltage (V
BAT
), the charge
program currently selected (SEAL or FLOOD), the
day/night status detected by the PV module. The
load icon, if ON, indicates that the load is power
supplied.
button
It displays the current (I
PAN
) of the PV module. We
remember that the current delivered by the PV
module depends on its state of sun-lighting and on
battery charge status. With charged battery
(Vbatt>14,4V @12V or Vbatt>28,8V @24V) even
with a good lighting of the PV module, you have
low currents from PV module since the regulator
limits the current to avoid battery overcharge.
button
PV module voltage (V
PAN
).
button
It displays the power in watt actually delivered by
the PV module.
button
It displays the counter of energy that is delivered
by the PV module in KWh. It is possible to reset
this measure pressing simultaneously the buttons
for 2 seconds.
button
It displays the charge current inside the battery
(I
CHARGE
).
button
It displays the battery temperature that is currently
measured by the temperature sensor connected
to WMARINE10.
button
It displays the current that is currently delivered to
the load; even if in this screen the load icon is on,
this does not mean that it is effectively power
supplied; in fact the load is controlled according to
the load management program that is currently
set.
button
It displays the power that is currently delivered to
the load in watt.
button
It displays the energy counter in KWh consumed
by the load. It is possible to reset this counter
pressing simultaneously the buttons
for 2
seconds.
button
Pressing the button you go back to the main page.
Fig. 3 Display pages of measures
System configuration
You can go to the configuration pages of
WMarine10 pressing simultaneously for at least 2
seconds the buttons
.
Charge program configuration page
It sets the charge voltage for the battery.
We recommend to set the SEAL program for
GEL or sealed batteries and the FLOOD
program for the charge of flooded lead acid
batteries. Charge voltages relating to each
one of the programs are indicated in the
following fig. 6/8 and must be chosen in
accordance with the battery manufacturer
indications.
Page change
Low Battery voltage configuration page
It sets the intervention voltage of Low battery
protection (load detachment in case of low
battery). When pressing the button
you
change the setting from 10.8V to 12.2V for
12V systems and from 21.6V to 24.4V for 24V
systems.
Page
change
Load management program configuration page
.
.
Load always
ON either
during day or
during night.
Load ON
only during
day.
Load ON
only during
night.
Load ON
during night
for 1 hour.
Load ON
during night
for 16 hours.
Page change
Voltage configuration page - Vday
WMARINE10 detects the day when the
voltage of PV module (V
PAN
) is > than V
DAY
threshold; it detects the night when V
PAN
is <
than V
NIGHT
threshold. In this page it is
possible to change V
DAY
threshold.
V
NIGHT
threshold = V
DAY
–1.3V
Page change
Software version display page
It displays the software version in use on
WMARINE10
Pressing the left button you go back to the configuration page of the
charge program
Fig. 4 Setting pages
Once modified the settings of WMarine10 these
become operative only after editing from the
configuration pages pressing simultaneously the
buttons
for at least 2 seconds.