background image

Safety Notes 

 

 

unless repair work or alignment is carried out properly. 

  Disable the existing sliding gate locks in order to avoid damages 

on the gate. 

  Ensure proper mounting when installing the sliding gate opener. 

Check the  sliding gate for proper manual operation. It is essen-
tial  that  the  sliding  gate  can  be  easily  opened  and  closed  by 
hand. 

  The  max.  permissible  gate  size  and  gate  weight  must  not  be 

exceeded. Using the gate opener on a larger and heavier gate is 
not permitted.

 

 

  The sliding gate opener may only be operated when monitored. 

  Do not allow children to play with the remote control. 

  Attach  the  warning  signs  well  visible  on  the  gate  and  inform  all 

user of the sliding gate opener about the risk during operation. 

 

 

 

 

 

 

 

  Do not modify the sliding gate opener in any way.  

  Only operate the gate opener if the gate is fully visible and there 

are  no  obstructions,  persons  or  animals.  Keep  persons  or  ani-
mals out of reach of the gate as long as the gate is not complete-
ly opened or closed. Do not allow children to stand or play in the 
gate

’s  moving  range.  Make  sure  movement  of  the  gate  and 

proper  function  of  the  sliding  gate  opener  are  not  impaired  by 
obstacles such as twigs, bushes or leaves. 

  Please mind  the  danger  area.  Do  not  grasp  moving  parts  while 

the sliding gate opener is in operation. There is risk of pinching! 

Install Warn Signs on both  

sides of the Gate! 

Summary of Contents for 84 67 47































Reviews: