Westinghouse WWT1084C7WA, User Manual

14

        www.westinghouse.com.au / www.westinghouse.co.nz

Water Level Touchpad

Choose the water level by pressing the 

“Water Level” touchpad. 
Use only the amount of water you need for 

the wash load.
Please refer the to program table on page 

Flood diagnostic is explained on 

page 30. You should refer to this if 

you have water pouring onto the 

floor. The display will show “       ” 

and you will hear rapid short beeps 

continuously to remind you about 

this problem.

Temp Touchpad 

For each wash program your washing 

machine automatically selects a suitable 

fill water temperature. If you want to use a 

different wash water temperature, press 

the Temperature button repeatedly. 

The temperature of warm water will 

depend on the temperature and pressure 

of your hot and cold water supplies. The 

recommended temperature for warm is 

35°C. 

You have four temperatures to choose 

from Hot, Warm, Normal and Cold.

The water temp lights will tell you the 

temperature for each press of the button.

Always check your label for the washing 

temperature symbols which the 

International Care Labelling Code now 

uses

If you have a cold water connection 

ONLY and the hot inlet valve is 

capped off (refer installation 

instructions) 

you must select Cold 

washes only.

You can adjust the flow rate of the water 

supplies to adjust the Warm temperature. 

All rinse water temperatures are cold.

Cold,

Warm,

Hot.

Pressing the Rinse touchpad to choose 

the rinse type for your wash load. For 

most washes, the machine automatically 

fills the full tub of water for a rinse.

Rinse Touchpad

There are four rinses to choose from 

Extra, Regular, Fast and Eco to remove 

the detergent from the clothes.

Extra rinse 

- 2 rinses cycles.

Regular rinse

 - 1 rinse cycle.

Fast rinse

 - Spraying water 3 rinses 

cycles.

Eco

 - Spraying water 4 rinses cycles. 

When Eco rinse is used, rinse water is 

sprayed into the washbowl in pulses. 

After each pulse the washbowl will spin 

to remove detergent laden water from 

the clothes.

How does Eco Rinse work?

The machine will go through a series of 

maximum 4 pulses spray and short spin 

cycles in this manner, depending on 

program selection, followed by a final 

long spin that removes the water from the 

clothes to complete the full wash 

program.

3.4 Options

Delay End Touchpad

Before you start the program, this option 

makes it possible to define the end of the 

washing program from minimum of 1 hour 

to maximum of 20 hours.

After selecting Delay End time, press 

Start/Pause touchpad to start the 

program. Machine will then countdown 

and update time on the display every 

hour until it reaches the starting point of 

the wash cycle.

Press the Delay End touchpad to choose 

the end time as you wish. The display 

shows the number of hours. 

For example, if the program duration of 

your selected program is 3.20 hours and 

you define the “Delay End” time to 6 

hours. This means your wash program 

will finish in 6 hours. (See diagram)

3.20 hrs.

2.40 hrs.

Program Cycle

 : 6 hrs.

Pressed 

Start/Pause

End of 

Cycle

Start the 

Program

Countdown

This option must be selected after 

choosing the wash program, and 

before pressing the “Start/Pause” 

touchpad. 

If you wish to modify or cancel Delay End 

option after starting the program, follow 

the steps below:

set the washing machine to PAUSE by 

pressing “Start/Pause” touchpad;

-

deselect this option by pressing

“Delay End” touchpad repeatedly till

the display shows delay time “       ”;

-

press the “Start/Pause” to start the 

program.

-

Press this touchpad to select the spin 

speed or no spin, if you want your 

laundry to be spun at a speed different 

from the one proposed by the washing 

machine.
The speed of spin level are:
–

 High

, about 800 rpm ;

–

 Mid

, about 650 rpm ;

–

 Low

, about 550 rpm.

–

 No Spin

, 0 rpm.

Spin Touchpad

This option allows you to soak heavily 

soiled clothes at the beginning of the 

wash. To do this, press the Soak touchpad 

to select the soak time.

Soak Touchpad

The lid must be closed to allow Soak 

functions to operate. The machine will 

agitate for short periods. At other times, 

the clothes are soaking and the machine 

will be doing nothing.

Note:

Compare this with Regular rinse 

where much more water is used.
Regular rinse, water enters the 

machine filling up to the wash water 

level selected. The washer agitates 

and finally empties the rinse water 

through the drain hose. 
Extra rinse, this is a special option for 

those people who suffer from 

allergies, this extra rinse will provide 

2 rinses to ensure all detergent 

residue has been removed.
Select Regular rinse if you are going 

to use fabric softener. 
Regular rinse ensures the fabric 

softener is correctly dispensed and 

thoroughly removed from your 

clothes during rinsing.