-8-
-13-
NOTE:
The Tomato & Fruit Strainer Attachment
cannot be used with meat products.
NOTE:
Follow the “Food Safety Guidelines” in this
manual and as outlined by the U.S. Food and Drug
Administration (FDA) whenever using this appliance.
Keep meat/food refrigerated and covered. Do not
let meat/food sit out any longer than is necessary for
processing.
1. Cut large fruits and vegetables into quarters and
small fruits and vegetables in half.
IMPORTANT:
Remove pits, stems, shells
and seeds before placing fruits or vegetables
into the
Tomato & Fruit Strainer
to avoid
damaging the
Screen.
2. Place the fruits/vegetables in the
Tray
. Do not
overfill the
Tray
.
DO NOT
operate the
Grinder
without
the
Tray
in place.
3. Place a bowl under the
Plastic Chute
to collect juice and pulp. Place a bowl
under the
Screen
outlet to collect skin and seeds.
4. Feed the fruits/vegetables into the
Grinder Head
. Use the
Stomper
to push the
fruits/vegetables into the
Grinder Head
.
Never use your fingers!
11. When straining is complete, turn the
Motor Unit
“off” and disconnect it from the
electrical outlet.
HELPFUL HINTS:
A.
Rerun the skin and seeds through the
Food Strainer
to extract any
leftover pulp & juice. Repeat as necessary.
B.
Use a rubber spatula to scrape pulp from the
Screen
into the
Chute
.
USING THE TOMATO & FRUIT
STRAINER
Not included with all grinders.
STUFFER ASSEMBLY
1. Place the
Plastic Washer
then the
Bushing Set
onto the end of the
Auger
opposite
the
Pin
(figure 3).
2. Carefully insert the
Auger
into the
Grinder Head.
3. Place the
Knife
onto the square portion of the
Auger Pin
. The cutting edges of the
Knife
should face outward (figure 4).
4. Place the
Coarse Grinder Plate
onto the round portion of the
Auger Pin
. Align the
tabs on the
Grinder Plate
with the notches in the
Grinder Head
.
5. Insert the
Stuffing Funnel
through the
Front Ring Nut
(figure 3).
6. Screw the
Front Ring Nut/Stuffing Funnel
assembly onto the
Grinder Head
until
firmly tight.
DO NOT
over-tighten the
Front Ring Nut
to avoid damaging the
Grinder
during operation.
7. Loosen the
Head Locking Knob
on the side of the
Motor Unit
.
8. Install the
Grinder Head
onto the
Motor Unit
(figure 3).
9. Tighten the
Head Locking Knob
to secure the
Grinder Head
.
10. Install the
Tray
onto the
Grinder Head
. Press the
Tray
down until fully seated (figure 3).
Figure 3
Front
Ring
Nut
Auger
Plastic
Washer
Grinder
Head
Motor
Unit
Tray
Stomper
Head
Locking
Knob
Knife
with
cutting
edges
facing
outward.
Figure 4
Grinding
Plate
Stuffing
Funnel
8. Install and firmly tighten the
Front Ring
Nut
(make sure the tabs remain aligned with the
notches).
DO NOT
over-tighten the
Front Ring Nut
to avoid damaging the
Grinder
during operation.
9. Loosen the
Head Locking Knob
on the side
of the
Motor Unit
.
10. Insert the
Screen
end of the fully-assembled
Grinder Head
through the outlet end of the
Plastic
Chute
(figure 9).
11. Install the
Grinder Head
onto the
Motor Unit
.
12. Tighten the
Head Locking Knob
to secure the
Head
in place.
13. Install the
Tray
onto the
Grinder Head
. Press the
Tray
down until fully seated (figure 9).
Figure 9
Reverse
Button
Power
Switch
Auger
Pin
Bushing
Set
WARNING!
Before cleaning, assembling or disassembling the
Grinder
, make sure
it is turned “off” and disconnected from the power source. Test to make sure there is
no power to the
Grinder
by switching the
Motor Unit
“on” and “off.”
Follow all of the Safety Rules
and Warnings in this manual
whenever using this appliance.
Never leave this
appliance unattended.
Disconnect from power supply
when not in use.
WARNING!
Keep fingers, hands,
other body parts and
foreign objects away
from the inlet during
operation!
Only use the provided
stomper to push food into
the appliance.
Keep children away!