background image

Model # BBXL54NV 

Please call for replacement parts or assistance: 

1-866-942-5362

 

Whalen Furniture Manufacturing   

 

           Page 24                                 Factory No. 16434 

Care and Maintenance 

 

  Use a soft, clean cloth that will not scratch the surface when dusting. 

  Use of furniture polish is not necessary. Should you choose to use polish, test first in an 

inconspicuous area. 

  Using solvents of any kind on your furniture may damage the finish. 

  Never use water to clean your furniture as it may cause damage to the finish. 

  Always use coasters under beverage glasses and flowerpots. 

  Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid 

rubbing. 

  Always use protective pads under hot dishes and plates. Heat can cause chemical changes that 

may create spotting within the furniture finish. 

  Stains or marks from crayons or ink markers will be difficult to remove. 

  In the event that your furniture is stained or otherwise damaged during use, we recommend that 

you call a professional to repair your furniture. 

 Check 

bolts/screws 

periodically 

and tighten them if necessary. 

 
 

Further advice about furniture care 

 

It is best to keep your furniture in a climate-controlled environment. Extreme temperature and 
humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep 
furniture away from direct sunlight as sun may damage the finish. 

 

Proper care and cleaning at home will extend the life of your purchase. Following these important 
and helpful tips will enhance your furniture as it ages. 

 

A Touch-up Pen has been provided to repair any small nicks or scratches that may occur 
during assembly or shipping. 

We hope you enjoy your purchase for many years. 

Thank you for your purchase! 

 
 

QUALITY GUARANTEE 

 

We are confident that you will be delighted with your Whalen Furniture purchase. 

 

Should this product be defective in workmanship or materials or fail under normal use, we will repair 
or replace it for up to one (1) year from the date of purchase. Every Whalen Furniture product is 
designed to meet your highest expectations. We guarantee that you will immediately see the value of 
our fine furniture. 

 

This warranty gives you specific legal rights and you may also have other rights which vary from 
State to State (province to province). 

 

Customer Service: 1-866-942-5362 

8:30 a.m. - 4:30 p.m., PST, Monday to Friday 

www.whalenfurniture.com 

Summary of Contents for BBXL54NV


























Reviews: