background image

12 

Care and Maintenance 

 

 

Use a soft, clean cloth that will not scratch the surface when dusting. 

 

Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. 

 

Using solvents of any kind on your furniture may damage the finish. 

 

Never use water to clean your furniture as it may cause damage to the finish. 

 

Always use coasters under beverage glasses and flowerpots. 

 

Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently. Avoid rubbing. 

 

Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create 
spotting within the furniture finish. 

 

In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a 
professional to repair your furniture. 

 

Check bolts/screws periodically and tighten them if necessary. 

 
 

Further Advice about Wood Furniture Care 

 
It  is  best  to  keep  your  furniture  in  a  climate-controlled  environment.  Extreme  temperature  and  humidity 
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from 
direct sunlight as sun may damage the finish. 

 

Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful 
tips will enhance your furniture as it ages. 

 

A touch-up pen has been provided to minimize the small nicks or scratches that may occur during assembly or 
shipping. 

 

We hope you enjoy your purchase for many years. 

Thank you for your purchase! 

 
 

QUALITY GUARANTEE 

We are confident that you will be delighted with your Whalen Furniture purchase. 
Should  this  product  be  defective  in  workmanship  or  materials  or  fail  under  normal  use,  we  will  repair  or 
replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet 
your highest expectations. We guarantee that you will immediately see the value of our fine furniture. 
This warranty gives you specific legal rights and you may also have other rights which vary from state to state 
or province to province. 

 

Whalen Furniture Manufacturing, 

1578 Air Wing Road 

San Diego CA, 92154 USA 

Customer Service: 1-866-942-5362 

8:30 a.m. - 4:30 p.m., PST, Monday to Friday 

www.whalenfurniture.com

 

Summary of Contents for BJKC













Reviews: