background image

Model # ODUS-CGTP 

Please call for replacement parts or assistance: 

1-866-942-5362

 

Whalen Furniture Mfg., Inc.   

 

 

     Page 18                                                Factory No. 16015 

Care and Maintenance 

 

 

Use a soft, clean cloth that will not scratch the surface when dusting. 

 

Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. 

 

Using solvents of any kind on your furniture may damage your furniture’s finish. 

 

Never use water to clean your furniture as it may cause damage to the finish. 

 

Always use coasters under beverage glasses and flowerpots. 

 

Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing. 

 

Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create 
spotting within the furniture finish. 

 

Stains or marks from crayons or ink markers will be difficult to remove. 

 

In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a 
professional to repair your furniture. 

 

Check bolts/screws periodically and tighten them if necessary. 

 
 
 

Further advice about wood furniture care 

 

It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity 
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from 
direct sunlight as sun may damage the finish. 
 
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful 
tips will enhance your furniture as it ages. 

 

A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during assembly or 
shipping. 

 

We hope you enjoy your purchase for many years. 

Thank you for your purchase! 

 
 
 

QUALITY GUARANTEE 

 

We are confident that you will be delighted with your Whalen Furniture purchase. 

 

Should this product be defective in workmanship or materials or fail under normal use, we will repair or 
replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet 
your highest expectations. We guarantee that you will immediately see the value of our fine furniture. 

 

This warranty gives you specific legal rights and you may also have other rights which vary from State to State. 

 

Customer Service: 1-866-942-5362 

 

8:30 a.m. - 4:30 p.m., PST, Monday to Friday 

 

www.whalenfurniture.com

 

Summary of Contents for Jasper Chrome & Glass Pier




















Reviews: