background image

For your safety 

These instructions have been drawn up for your safety and that of others. You are 
therefore requested to read them carefully before installing and using the appliance. 
Keep this instruction manual for future reference as necessary. If the appliance is 
sold or moved, make sure that the manual is handed over to the new user

.     

Installation

 

·

Installation of the appliance and its connection to the electrical mains must only be 
carried  out  by  QUALIFIED  PERSONEL.  Before  doing  any  servicing,  it  is 
important  to  check  that  the  appliance  is  DISCONNECTED  from  the  electrical 
mails. 

·

It is risky to modify or attempt to modify the characteristics of this product. 

·

After removing the appliance from the packaging, make sure that it is not damaged 
and  that  the  electrical  lead  is  in  perfect  condition.  Otherwise,  contact  your  dealer 
before putting the appliance into operation.   

·

The  Manufacturer  declines  all  responsibility  in  case  of  failure  to  comply  with  the 
accident prevention regulations. 

·

Make sure that air    circulates freely around the appliance. Poor ventilation creates a 

shortage of oxygen 

·Use of a gas cooking appliance produces heat and moisture in the room 

in which it is ins

talled. Ensure that the room is well ventilated by keeping the air 

intakes  open  and  in  good  working  order  or  by  installing  an  extractor  hood  with 
discharge pipe. 

·If the

  appliance  is  used  intensively  for  a  long  time  the  effectiveness  of  the 

ventilation  will  have  to  be  increased,  for  example  by  opening  a  window  or 
increasing the power of any electric extractor fan. 

 

During use 

·

This  product  is  designed  to  cook  food  inside  ordinary  homes  and  for 

non-professional purposes. It should not be used for any other purpose. 

·

 

After using the appliance, make sure that all controls are in “CLOSED” or “OFF” 

position. 

·

 

If you use an electrical socket close to this appliance, take care that the cables of the 

appliances you are using are far away from the hot parts of this appliance. 

·

Never  leave  plastic,  oil  or  any  other  flammable  material  around  the  hob  when 

cooking. 

·

If the Hob fails to light at the first time, then you should wait for I minute before you 

try again. 

                                                                                                                                     

 

Summary of Contents for AKC 640















Reviews: