background image

 

 

These instructions have been drawn up for your safety and that of others. You 

are  therefore  requested  to  read  them  carefully  before  installing  and  using  the 
appliance.  Keep  this  instruction  manual  for  future  reference  as  necessary.  If  the 
appliance is sold or moved, make sure that the manual is handed over to the new 
user

.     

Installation

 

·

Installation of the appliance and its connection to the electrical mains must only be 
carried out by QUALIFIED PERSONNEL. Before any procedure, it is important to 
check that the appliance is DISCONNECTED from the electrical mains. 

·

It is risky to modify or attempt to modify the characteristics of this product. 

·

After removing the appliance from the packaging, make sure that it is undamaged 
and  that  the  electrical  lead  is  in  perfect  condition.  Otherwise,  contact  your  dealer 
before putting the appliance into operation.   

·

The  manufacturer  declines  all  responsibility  in  case  of  failure  to  comply  with  the 
accident prevention regulations. 

·

Make sure that air is able to circulate freely around the appliance. Poor ventilation 
produced a shortage of oxygen. 

· 

Make  sure  that  the  appliance  is  supplied  with  the  type  of  gas  indicated  on  the 

relative sticker next to the mains gas connection pipe. 

· 

Use of a gas cooking appliance produces heat and moisture in the room which it is 

installed.  Ensure  that  the  room  is  well  ventilated  by  keeping  the  air  intakes  open 
and in good working order or by installing an extractor hood with discharge pipe. 

· 

If  the  appliance  is  used  intensively  for  a  long  time,  the  effectiveness  of  the 

ventilation  will  have  to  be  increased,  for  example  by  opening  a  window  or 
increasing the power of electric extractor fan. 

 
These instructions are only valid if the country symbol appears on the appliance. If 
the symbol does not appear on the appliance, it is necessary to refer to the technical 
instructions which will provide the necessary instructions concerning modification of 
the appliance to the conditions of use of the country 
 

As a p

reamble, they shall include the following warnings:   

“Prior to installation, ensure that the local distribution conditions (nature of the gas 
and gas pressure) and the adjustment of the appliance are compatible.” 
 
 
                                                                                                                                  2 

Summary of Contents for AKC7250 C/BLM



















Reviews: